Manuals / Fluke / Marine Equipment / Marine Radio

Fluke 199, 196, 192 Analyzing a TrendPlot or Scope Record, Triggered Single Sweep Recording

Models: 192 196 199

1 116

Download 116 pages 43.11 Kb

Page 42

Fluke 192/196/199

Users Manual

The test tool starts recording after receiving the start signal. All samples are continuously saved in deep memory until the memory is full. The last nine recorded divisions are displayed on the screen. Use View All to display the full memory contents.

Note

To learn more about the Single Shot trigger function, see Chapter 5 “Triggering on Waveforms”.

Analyzing a TrendPlot or Scope Record

From a Scope TrendPlot or Scope Record you can use the analysis functions CURSORS and ZOOM to perform detailed waveform analysis. These functions are described in Chapter 4: “Using Replay, Zoom and Cursors”.

Figure 20. Triggered Single Sweep Recording

34

Image 42

Fluke 199, 196, 192 user manual Analyzing a TrendPlot or Scope Record, Triggered Single Sweep Recording

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using Replay, Zoom and Cursors Using The MultimeterUsing The Recorder Functions Fluke 192/196/199Iii Specifications IndexStatement of Conformity Declaration of ConformityManufacturer Sample testsUnpacking the Test Tool Kit ScopeMeter Test Tool KitDescription # DescriptionSafety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Resetting the Test Tool Screen After ResetNavigating a Menu Open the Waveform OptionsHiding Key Labels and Menus Input ConnectionsMaking Scope Connections Scope ConnectionsDisplaying an Unknown Signal with Connect-and-View Screen After an Auto SetMaking Automatic Scope Measurements Select the Peak-PeakMeasurement Freezing the Screen Hz and V peak-peak as Scope ReadingsUsing Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Displaying Glitches Suppressing High Frequency NoiseAcquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Mathematics menu Analyzing WaveformsMathematics... to open Or a vs BUsing The Multimeter Making Meter ConnectionsMaking Multimeter Measurements Measuring Resistance ValuesOpen the Current Probe Making a Current MeasurementHighlight a ac SubmenuAmpere Measurement Readings Freezing the Readings Selecting Auto/Manual RangesMaking Relative Measurements Making a Relative MeasurementUsing The Recorder Functions Opening the Recorder Main MenuPlotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope Displaying Recorded Data TrendPlot ReadingOpen the Recorder Options Changing the Recorder OptionsTurning Off the TrendPlot Display MenuRecording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Analyzing a TrendPlot or Scope Record Triggered Single Sweep RecordingUsing Replay, Zoom and Cursors Replaying the 100 Most Recent Scope ScreensReplaying Step-by-Step Replaying a WaveformReplaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in on a Waveform Zooming in a WaveformDisplaying the Zoomed Waveform Turning Off the Zoom FunctionUsing Horizontal Cursors on a Waveform Making Cursor MeasurementsUsing Vertical Cursors on a Waveform Turn off the cursorsUsing Cursors on a A+B, A-B or A*B Waveform Making Rise Time MeasurementsTriggering on Waveforms Setting Trigger Level and Slope Screen with all Trigger InformationUsing Trigger Delay or Pre-trigger Trigger Delay or Pre-trigger ViewAutomatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Select Free Run, jump to Noise Triggering on EdgesOpen the Trigger Options menu Open the Trigger on Edge menu Reject FilterSelect On Trigger, jump to Noise Triggering on Noisy WaveformsMaking a Single Acquisition Set Noise reject Filter to OnMaking a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Finding Missing Pulses Open the Trigger Options menu Select On TriggerTriggering on Missing Pulses Using Memory, PC and Printer Saving and RecallingSaving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Recalling a Setup Configuration Viewing Stored Screens Scroll through all stored screensConnecting to a Computer Documenting ScreensConnecting to a Printer Connecting a Serial PrinterPrinting a Screen Setting up the Printing ConfigurationOpen the Printer Setup submenu Baud RateFluke 192/196/199 Using the Standard Accessories TipsProbing Using 2-mm Heavy Duty Test Probes Heavy Duty Fixed Connections for ScopeTips Using the Standard Accessories Using the Independently Floating Isolated Inputs Measuring Using Independently Floating Isolated InputsTips Using the Independently Floating Isolated Inputs Turn the test tool off Using the Tilt StandSuppressing Key Labels and Menu’s Press and holdOpen the Language Select Adjusting the Contrast and BrightnessChanging the Information Language Accept French as the languageChoose 1999, jump to Month Open Date Adjust menuChanging Date and Time Choose 04, jump to DaySaving Battery Life Setting the Power Down TimerTo Coupling Open the User Options menu Open the Auto Set Adjust MenuChanging the Auto Set Options Select UnchangedCleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the BatteriesExtending Battery Operation Time Open the User Options menuSelect 101, then return Replacing the NiMH Battery Pack BP190Calibrating the Voltage Probes Select Voltage, then jump toMaintaining the Test Tool Displaying Calibration Information Parts and AccessoriesStandard Accessories Open the Version & CalibrationStandard Accessories Ordering CodeTL24 General Purpose Leads RS200 Optional Accessories Troubleshooting Battery Operated Fluke Accessories Do Not Function FlukeView Does Not Recognize The Test ToolSafety Characteristics SpecificationsPerformance Characteristics IntroductionDual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Edge Trigger Trigger and DelayAutomatic Connect-and-View Trigger Isolated External TriggerAutomatic Scope Measurements AC Voltage VAC AC+DC Voltage True RMSFrequency Hz Amperes AMPPeak Duty Cycle DutyTemperature Temp PowerPhase Decibel dBMeter DMM Measurements on Meter InputsWith Optional Temperature Probe DiodeRecorder TrendPlot Meter or ScopeScope Record Zoom, Replay and Cursors MiscellaneousOptical InterfacePort Probe CalibrationMemory MechanicalEnvironmental Safety Max. Input VoltagesMax. Floating Voltage Probe SafetyElectrical specifications Environmental102 Electromagnetic Immunity Disturbance less than 10% of full scale = 3V/m104 Index Numerics106 107 108