Using Persistence to Display Waveforms | Fluke 199, 196, 192

Fluke 192/196/199

Users Manual

Using Persistence to Display Waveforms

When persistence is selected, the test tool displays the upper and lower boundaries of dynamic waveforms.

1						Display the SCOPE key labels.



2						Open the Waveform Options
2						Open the Waveform Options
						menu.
						menu.

3						Jump to Waveform: and Select
3						Jump to Waveform: and Select
						Persistence , then select Infinite.
						Persistence , then select Infinite.

4 Start monitoring the waveform.

Figure 10. Using Persistence to Display Waveform

Variations

Observe that the fluctuating portion of the waveform appears in gray on the screen. See Figure 10.

You can use persistence to observe variations in time or amplitude of input waveforms over time.

16

Image 24

Fluke 199, 196, 192 Using Persistence to Display Waveforms, Jump to Waveform and Select, Persistence , then select Infinite

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using The Multimeter Using The Recorder FunctionsUsing Replay, Zoom and Cursors Fluke 192/196/199 Iii Specifications Index Declaration of Conformity ManufacturerStatement of Conformity Sample tests Unpacking the Test Tool Kit ScopeMeter Test Tool Kit Description # Description Safety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Resetting the Test Tool Screen After Reset Navigating a Menu Open the Waveform Options Hiding Key Labels and Menus Input Connections Making Scope Connections Scope Connections Displaying an Unknown Signal with Connect-and-View Screen After an Auto Set Making Automatic Scope Measurements Select the Peak-PeakMeasurement Freezing the Screen Hz and V peak-peak as Scope Readings Using Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Displaying Glitches Suppressing High Frequency Noise Acquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Analyzing Waveforms Mathematics... to openMathematics menu Or a vs B Using The Multimeter Making Meter Connections Making Multimeter Measurements Measuring Resistance Values Making a Current Measurement Highlight a acOpen the Current Probe Submenu Ampere Measurement Readings Freezing the Readings Selecting Auto/Manual Ranges Making Relative Measurements Making a Relative Measurement Using The Recorder Functions Opening the Recorder Main Menu Plotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope Displaying Recorded Data TrendPlot Reading Changing the Recorder Options Turning Off the TrendPlot DisplayOpen the Recorder Options Menu Recording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Analyzing a TrendPlot or Scope Record Triggered Single Sweep Recording Using Replay, Zoom and Cursors Replaying the 100 Most Recent Scope Screens Replaying Step-by-Step Replaying a Waveform Replaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in on a Waveform Zooming in a Waveform Displaying the Zoomed Waveform Turning Off the Zoom Function Using Horizontal Cursors on a Waveform Making Cursor Measurements Using Vertical Cursors on a Waveform Turn off the cursors Using Cursors on a A+B, A-B or A*B Waveform Making Rise Time Measurements Triggering on Waveforms Setting Trigger Level and Slope Screen with all Trigger Information Using Trigger Delay or Pre-trigger Trigger Delay or Pre-trigger View Automatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Triggering on Edges Open the Trigger Options menu Open the Trigger on Edge menuSelect Free Run, jump to Noise Reject Filter Triggering on Noisy Waveforms Making a Single AcquisitionSelect On Trigger, jump to Noise Set Noise reject Filter to On Making a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Finding Missing Pulses Open the Trigger Options menu Select On Trigger Triggering on Missing Pulses Using Memory, PC and Printer Saving and Recalling Saving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Recalling a Setup Configuration Viewing Stored Screens Scroll through all stored screens Connecting to a Computer Documenting Screens Connecting to a Printer Connecting a Serial Printer Setting up the Printing Configuration Open the Printer Setup submenuPrinting a Screen Baud Rate Fluke 192/196/199 Using the Standard Accessories Tips Probing Using 2-mm Heavy Duty Test Probes Heavy Duty Fixed Connections for Scope Tips Using the Standard Accessories Using the Independently Floating Isolated Inputs Measuring Using Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Using the Tilt Stand Suppressing Key Labels and Menu’sTurn the test tool off Press and hold Adjusting the Contrast and Brightness Changing the Information LanguageOpen the Language Select Accept French as the language Open Date Adjust menu Changing Date and TimeChoose 1999, jump to Month Choose 04, jump to Day Saving Battery Life Setting the Power Down Timer Open the User Options menu Open the Auto Set Adjust Menu Changing the Auto Set OptionsTo Coupling Select Unchanged Cleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the Batteries Extending Battery Operation Time Open the User Options menu Replacing the NiMH Battery Pack BP190 Calibrating the Voltage ProbesSelect 101, then return Select Voltage, then jump to Maintaining the Test Tool Parts and Accessories Standard AccessoriesDisplaying Calibration Information Open the Version & Calibration Standard Accessories Ordering Code TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting Battery Operated Fluke Accessories Do Not Function FlukeView Does Not Recognize The Test Tool Specifications Performance CharacteristicsSafety Characteristics Introduction Dual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Trigger and Delay Automatic Connect-and-View TriggerEdge Trigger Isolated External Trigger Automatic Scope Measurements AC Voltage VAC AC+DC Voltage True RMS Amperes AMP PeakFrequency Hz Duty Cycle Duty Power PhaseTemperature Temp Decibel dB Meter DMM Measurements on Meter Inputs With Optional Temperature Probe Diode Recorder TrendPlot Meter or ScopeScope Record Zoom, Replay and Cursors Miscellaneous Probe Calibration MemoryOptical InterfacePort Mechanical Environmental Safety Max. Input VoltagesMax. Floating Voltage Safety Electrical specificationsProbe Environmental 102 Electromagnetic Immunity Disturbance less than 10% of full scale = 3V/m 104 Index Numerics 106 107 108