Command block registers, Data register X’1F0’ | Fujitsu MHU2100AT

Interface

Device/Head, Cylinder High, Cylinder Low, Sector Number registers indicate LBA bits 27 to 24, bits 23 to 16, bits 15 to 8, and bits 7 to 0, respectively.

If the LBA mode is specified with 48-bit address information, the Cylinder High, Cylinder Low, Sector Number registers are set twice. In the first time, the registers indicate LBA bits 47 to 40, bits 39 to 32, and bits 31 to 24, respectively. In the second time, the registers indicate LBA bits 23 to 16, bits 15 to 8, and bits 7 to 0, respectively.

5.2.2 Command block registers

(1) Data register (X’1F0’)

The Data register is a 16-bit register for data block transfer between the device and the host system. Data transfer mode is PIO or DMA mode.

(2) Error register (X’1F1’)

The Error register indicates the status of the command executed by the device. The contents of this register are valid when the ERR bit of the Status register is 1.

This register contains a diagnostic code after power is turned on, a reset , or the EXECUTIVE DEVICE DIAGNOSTIC command is executed.

[Status at the completion of command execution other than diagnostic command]

	Bit 7		Bit 6	Bit 5	Bit 4	Bit 3	Bit 2	Bit 1	Bit 0

	ICRC		UNC	X	IDNF	X	ABRT	TK0NF	AMNF

X: Unused

-Bit 7: Interface CRC Error (ICRC). This bit indicates that a CRC error occurred during Ultra DMA transfer.

-Bit 6: Uncorrectable Data Error (UNC). This bit indicates that an uncorrectable data error has been encountered.

-Bit 5: Unused

-Bit 4: ID Not Found (IDNF). This bit indicates an error except for bad sector, uncorrectable error and SB not found.

-Bit 3: Unused

-Bit 2: Aborted Command (ABRT). This bit indicates that the requested command was aborted due to a device status error (e.g. Not Ready, Write Fault) or the command code was invalid.

5-8	C141-E202-01EN

Image 84

Fujitsu MHU2100AT manual Command block registers, Data register X’1F0’, Error register X’1F1’, UNC Idnf

Contents

MHU2100AT Disk Drive Product Manual For Safe Operation Handling of This Manual Revision History This page is intentionally left blank Preface Overview of Manual Conventions for Alert Messages Operating EnvironmentConventions Liability Exception This page is intentionally left blank Important Alert Items Important Alert Messages This page is intentionally left blank MHU2100AT Disk Drive Maintenance Manual Manual OrganizationMHU2100AT Disk Drive Product Manual This page is intentionally left blank Contents Installation Conditions Theory of Device Operation Contents Interface 100 120 Operations Glossary GL-1 Acronyms and Abbreviations AB-1 Index IN-1 Illustrations Figures Execution example of Read Multiple command Surface temperature measurement points and standard Tables 25 Relationship between combination of Identifier This page is intentionally left blank Device Overview Features Functions and performanceAdaptability Error correction and retry by ECC Connection to ATA interfaceData buffer Read-ahead cache system Device Specifications Specifications summarySpecifications 1 Specifications 2 Model and product numberMHU2100AT Examples of model names and product numbers Power Requirements Input VoltageRipple Current and power dissipation Environmental Specifications Current fluctuation Typ. at +5 V when power is turned onPower on/off sequence Environmental specifications Acoustic noise specification Shock and vibration specificationAcoustic Noise Shock and Vibration Service life Data assurance in the event of power failureReliability Mean time between failures Mtbf Error Rate Unrecoverable read errorPositioning error Media Defects Advanced Power Management Advanced Power Management Advanced Power Management This page is intentionally left blank Device Configuration Device Configuration System Configuration ATA interface2 1 drive connection Read/write circuit 2 drives configuration 3 2 drives connection Installation Conditions Dimensions Dimensions Mounting Integration Guidance C141-E144Orientation Frame Limitation of mountingPCA Location of breather Ambient temperature Service area Handling cautions Handling cautions Device connector Cable Connections Cable connector specifications Cable connector specificationsDevice connection FCI Jumper Settings Power supply connector CN1Location of setting jumpers Factory default setting Master drive-slave drive setting Csel setting 14 Csel setting Power Up in Standby setting 16 Example 2 of Cable Select Theory of Device Operation Outline SubassembliesDisk Spindle Circuit Configuration Air filterServo circuit Spindle motor driver circuit Power Supply Configuration PCA Power-on Sequence Power-on operation sequence Self-calibration contents Self-calibration Command processing during self-calibration Execution timing of self-calibration Read/write Circuit Read/write preamplifier PreAMPWrite circuit RLL code Meeprml Read circuit AGC circuitProgrammable filter circuit Digital PLL circuit FIR circuitD converter circuit Viterbi detection circuit Servo Control Servo control circuit Power amplifier Microprocessor unit MPUServo burst capture circuit A converter DAC Spindle motor control circuit Driver circuitVCM current sense resistor CSR Data-surface servo format Inner guard bandData area Outer guard band Physical sector servo configuration on disk surface Servo frame format Actuator motor control Operation to move the head to the reference cylinderSeek operation Track following operation Start mode Acceleration modeStable rotation mode Spindle motor control Theory of Device Operation Interface Interface signals Physical Interface Signal assignment on the connector Signal assignment on the interface connectorDA1 PDIAG-, Cblid DA0 DA2 Dasp GND Mstr DiowStop Dior Pdiag CblidDasp Iordy Logical Interface 1 I/O registers I/O registersDA2 DA1 DA0 Command block registers Error register X’1F1’Data register X’1F0’ UNC Idnf Features register X’1F1’ SET Multiple ModeSector Count register X’1F2’ Sector Number register X’1F3’ Cylinder Low register X’1F4’Cylinder High register X’1F5’ Device/Head register X’1F6’ DEV HS3 HS2 HS1 HS0Status register X’1F7’ BSY Interface Command register X’1F7’ Control block registersAlternate Status register X’3F6’ Host Commands Command code and parametersDevice Control register X’3F6’ HOB Srst Command code and parameters 1 Command NameParameter Used Command code and parameters 2 EXT Flush Cache EXT Host Commands Command descriptions Host Commands Recalibrate X’10’ to X’1F’ Read Sectors X’20’ or X’21’ MSB End head No. / LBA MSB Read Long X’22’ or X’23’ Write Sectors X’30’ or X’31’ 1F7 HST Status information 1F6 HDH Write Long X’32’ or X’33’ Write Verify X’3C’ Read Verify Sectors X’40’ or X’41’ Seek X’70’ to X’7F’ Execute Device Diagnostic X’90’ Diagnostic code Host Commands Initialize Device Parameters X’91’ Download Micro Code X’92’ Operation of Download Micro Code Standby Immediate X’94’ or X’E0’ Idle Immediate X’95’ or X’E1’ Standby X’96’ or X’E2’ Idle X’97’ or X’E3’ Host Commands Check Power Mode X’98’ or X’E5’ ’FF’ Sleep X’99’ or X’E6’ Smart X’B0 Features Register values subcommands and functions 1 Features Register values subcommands and functions 2 Smart Enable OperationsSmart Disable Operations Smart Read LOG Features Register values subcommands and functions 3 Smart ENABLE/DISABLE Auto OFF-LINE’DA’ Smart Return Status Interface Format of device attribute value data 1FFFormat of insurance failure threshold value data Data format version number Attribute ID Status Flag Current attribute valueAttribute value for the worst case so far Raw attribute value 10 Off-line data collection status Self-test execution status11 Self-test execution status Off-line data collection capability 12 Off-line data collection capabilityFailure prediction capability flag 13 Failure prediction capability flag Error logging capability 14 Error logging capabilityCheck sum Insurance failure threshold Smart error logging 16 Data format of Smart Summary Error Log Command data structure Error data structureTotal number of drive errors 17 Data format of Smart Comprehensive Error Log Smart Self-Test 18 Smart self-test log data format1FC Self-test number 19 Selective self-test log data structure Test SpanCurrent LBA under test Current Span under test Feature Flags 20 Selective self-test feature flagsSelective Self-test pending time min Device Configuration XB1 Device Configuration RestoreDevice Configuration Freeze Device Configuration Identify Device Configuration Restore FR = C0h Device Configuration Freeze Lock FR = C1hDevice Configuration Identify FR = C2h Device Configuration SET FR = C3h Host Commands 21 Device Configuration Identify data structure Execution example of Read Multiple command Read Multiple X’C4’ MSB Write Multiple X’C5’ Interface SET Multiple Mode X’C6’ Interface Read DMA X’C8’ or X’C9’ End head No. / LBA MSB Write DMA X’CA’ or X’CB’ Interface Read Buffer X’E4’ Flush Cache X’E7’ Write Buffer X’E8’ Identify Device X’EC’ Identify Device DMA X’EE’ 22 Information to be read by Identify Device command 1 ’3FFF’ 22 Information to be read by Identify Device command 2 Word Command without interrupt supports 2, 4, 8 and 16 sectors = Supports the Host Protected Area feature set = Supports the CFA Compact Flash Association feature set Interface Host Commands Diagnosis Word Bit Reserved Security level High, 1 Maximum SET Features X’EF’ 23 Features register values and settable modes’AA’ ’BB’ Data Transfer Mode Advanced Power Management APM Automatic Acoustic Management AAM 24 Contents of Security SET Password data At command issuance I-O register contents 1F7 hCM 1F6 hDH When the master password is selected When the user password is selectedSecurity UNLOCKX’F2’ Host Commands Security Erase Prepare X’F3’ Security Erase Unit X’F4’ Security Freeze Lock X’F5’ At command issuance I-O register contents 1F7 hCM 1F6 hDH 26 Contents of security password Host Commands Read Native MAX Address X’F8’ SET MAX X’F9’ SET MAX Address SET MAX SET Password FR = 01h SET MAX Lock FR = 02h SET MAX Unlock FR = 03h SET MAX Freeze Lock FR = 04h Interface Read Sectors EXT X’24’ Option customizing Description Read DMA EXT X’25’ Option customizing Description Error reporting conditions HOB=0HOB=1 Read Multiple EXT X’29’ Option customizing Description Read LOG EXT X2F Optional command Customize Description Interface Write Sectors EXT X’34’ Option customizing Description Write DMA EXT X’35’ Option customizing Description SET MAX Address EXT X’37’ Option customizing Description SET MAX LBA Write Multiple EXT X’39’ Option customizing Description Write LOG EXT X’3F’ Optional command Customize Description Host Commands Read Verify Sectors EXT X’42 Option customizing Description Flush Cache EXT X’EA’ Option customizing Description Error posting 27 Command code and parameters 1 27 Command code and parameters 2 Command Protocol PIO Data transferring commands from device to hostExecute Device Diagnostic Initialize Device Parameters Read Sectors Command protocol Protocol for command abort PIO Data transferring commands from host to device Write Sectors command protocol Commands without data transfer Other commands DMA data transfer commandsRead Multiple EXT Write Multiple EXT Sleep Read DMA EXT Write DMA EXT Indentify Device DMA Normal DMA data transfer Ultra DMA Feature Set Overview Phases of operation Ultra DMA data in commandsInitiating an Ultra DMA data in burst Pausing an Ultra DMA data in burst Data in transfer Terminating an Ultra DMA data in burst Interface Ultra DMA Feature Set Ultra DMA data out commands Initiating an Ultra DMA data out burst Pausing an Ultra DMA data out burst Data out transfer Terminating an Ultra DMA data out burst Ultra DMA Feature Set Ultra DMA CRC rules Series termination required for Ultra DMA 28 Recommended series termination for Ultra DMADIOR-HDMARDY-HSTROBE DIOW-STOP Timing PIO data transferPIO data transfer timing 10 Multiword DMA data transfer timing mode Multiword data transfer Ultra DMA data transfer 11 Initiating an Ultra DMA data in burst Name Mode Comment Strobe 29 Ultra DMA data burst timing requirements 2 MIN MAX Mode Name Comment 30 Ultra DMA sender and recipient timing requirements Sustained Ultra DMA data in burst Dstrobe at deviceDD150 at device Dstrobe at host DD150 at host Host pausing an Ultra DMA data in burst DmarqDmack Stop Device terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst HostDA0, DA1, DA2 CS0, CS1 16 Initiating an Ultra DMA data out burst Sustained Ultra DMA data out burst Hstrobe at host DD150 at hostHstrobe at device DD150 at device Device pausing an Ultra DMA data out burst Device DMACK- host Stop host DDMARDY- deviceHstrobe host DD150 Host Host terminating an Ultra DMA data out burst 19 Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst Dmarq device DMACK- hostDD150 Host Power-on and reset Master and slave devices are present 2-drives configurationOnly master device is present This page is intentionally left blank Operations Device Response to the Reset Response to power-on Response to hardware reset Response to power-on Response to hardware reset Response to software reset Response to software reset Response to diagnostic command Response to diagnostic command Power Save Power save modeActive mode Active idle mode Standby mode Sleep mode Power commands Defect ProcessingSpare area Alternating processing for defective sectors Sector slip processingTrack slip processing Automatic alternating processing Automatic alternating processing Read-ahead Cache Data buffer structure8MB buffer 8,388,608 bytes Read Sectors EXT Read Multiple EXT Read DMA EXT Commands that are targets of caching Caching operationRead Multiple EXT Read Dmaext Data that is a target of caching Operations Using the read segment buffer Miss-hit Sequential Hit Full hit Partial hit Command that are targets of caching Write CacheCache operation Invalidation of cached data Status report in the event of an error Reset responseCashing function when power supply is turned on Enabling and disabling Write Cache This page is intentionally left blank Glossary Power save mode Rotational delayPIO Programmed input-output Positioning Status VCM This page is intentionally left blank Acronyms and Abbreviations This page is intentionally left blank Index AAM Index Information to be read by Identify Read Sectors Command Read Native MAX Address Surface temperature measurement This page is intentionally left blank Comment Form Japan This page is intentionally left blank C141-E202-01EN This page is intentionally left blank