Front Machine Labels | Grizzly G0740 specification

Front Machine Labels

1606

1605

1604

1603

1602

1607

1605

1608

1609

1612

16011613

16111610

REF	PART #	DESCRIPTION

1601	P07401601	MACHINE ID LABEL
1602	PLABEL-55B	ENTANGLEMENT HAZARD LABEL
1603	PLABEL-11C	EYE INJURY HAZARD LABEL
1604	PLABEL-12B	READ MANUAL LABEL
1605	P07401605	THREAD DIAL CHART LABEL
1606	P07401606	SPINDLE SPEED HAZARD
1607	P07401607	RELEASE BOLT NOTICE LABEL

REF	PART #	DESCRIPTION

1608	PLABEL-63B	DISCONNECT POWER LABEL
1609	PLABEL-50B	BIOHAZARD LABEL
1610	P07401610	MODEL NUMBER LABEL
1611	G8588	GRIZZLY NAMEPLATE
1612	P07401612	FLUID CAPACITIES LABEL
1613	P07401613	AUTHORIZED PERSONNEL NOTICE LABEL

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

Model G0740 (Mfg. Since 11/12)

-125-

Image 127

Grizzly G0740 owner manual Front Machine Labels

Contents

Model G0740 14 X 40 HIGH-PRECISION Toolroom Lathe Page Table of Contents 129 Maintenance Machine Description Manual Accuracy IntroductionContact Info Identification Controls Components Two-Speed Motor SwitchHeadstock Carriage Control Panel Tailstock Safety Foot BrakeEnd Gears Machine Data Sheet Tailstock Info Other Specifications Safety Instructions for Machinery SafetyPage Additional Safety for Metal Lathes Additional Chuck Safety Circuit Requirements for Power SupplyAvailability Full-Load Current Rating 50 ft Grounding InstructionsExtension Cords Minimum Gauge Size 12 AWG To correct wiring that is out of phase Correcting Phase Polarity Wiring Unpacking SetupNeeded for Setup Preparation Tool Box Inventory Figure Qty Box 1 Figure Qty Steady Rest Assembly InstalledPre-Installed Not Shown Qty Inventory Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations To lift and move the lathe Lifting & Moving Leveling Leveling & Mounting Lubricating Lathe AssemblyBolting to Concrete Floors To connect the power cord to the lathe Power ConnectionAdding Coolant Test run consists of verifying Test Run Stop Cross Slide Spindle Break-In Factory adjustments that should be verified Recommended Adjustments Operation Overview Operations MEDIUM-SIZE, Heavy Chucks Chuck & Faceplate Mounting Installation Removal Devices To install the chuck Chuck Installation Registration Marks Chuck RemovalTo remove the chuck Chuck Jaw Reversal Scroll Chuck ClampingTo reverse 2-piece jaws Mounting Workpiece Jaw Chuck To mount a non-concentric workpiece to the faceplate Faceplate Positioning Tailstock Using QuillInstalling Tooling Tailstock Tools Needed Qty Offsetting TailstockTo install tooling in the tailstock Removing Tooling To align the tailstock to the spindle center- line Aligning Tailstock to Spindle CenterlineTo offset the tailstock Items Needed QtyPage Mounting Dead Center in Spindle CentersDead Centers Live Centers To mount a center in the tailstock Removing Center from SpindleMounting Center in Tailstock Removing Center from Tailstock Mounting Workpiece Between Centers Steady Rest To install and use the steady rest Carriage & Slide Locks Follow Rest Compound Rest Four-Way Tool Post Installing Tool Top View Aligning Cutting Tool with Spindle CenterlineBelow are two common methods To align the cutting tool with the tailstock center To set the micrometer stop Adjustable Feed StopMicrometer Stop Tools Needed Qty Hex Wrench 5mm Spindle Speed Manual Feed Configuration Examples Setting Spindle Speed Setting Spindle Speed of 1600 RPM Power Feed Power Feed Controls Setting Power Feed Rate of 0.18mm/rev Setting Power Feed Rate End Gears Standard End Gear Configuration To configure the end gears Alternate Configuration Headstock Threading Controls Threading Apron Threading Controls Nut when required and prevent an apron crashThread Dial Odd Numbered TPI Thread Dial ChartTPI Divisible By Even TPI Not Divisible By ⁄4 or 3⁄4 Fractional TPI Chip Drawer27⁄8 TPI Biological & Poison Hazard Coolant System T10439-4 Pc. Carbide Insert Ccmt Boring Bar Set Accessories G7978-Rotary Phase Converter G9610-Test IndicatorG9611-Test Indicator G9612-Test Indicator Cleaning/Protecting MaintenanceSchedule Lubrication Task Frequency Lubrication To change the headstock oil Quick-Change Gearbox One-Shot Oiler Apron Ball Oilers & Oil Cup Longitudinal Leadscrew Handling & Care Hazards Coolant System Service To add coolant Adding CoolantChanging Coolant See Hazards on To prepare the lathe for storage Machine Storage Motor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible Solution Lathe Operation Symptom Possible Cause Possible Solution As necessary see Compound Rest Backlash AdjustmentCross Slide Gib Adjustment Leadscrew End Play AdjustmentTo remove leadscrew end play Front saddle gib adjustment screw Carriage Lock Clamp Belts Half Nut AdjustmentTo adjust the half nut To adjust the V-belts To adjust the brake and brake switch Brake & SwitchPage To replace the shear pin Leadscrew Shear Pin Replacement Shear Pin Gap Installation Gap Insert Removal InstallationGap Removal Wiring Safety Instructions Wiring Wiring Overview Component location index Model G0740 Mfg. Since 11/12 Component Location Index Safety Switch, To Work Lamp, Electrical Cabinet Wiring Electrical Box Electrical box wiring Model G0740 Mfg. Since 11/12 Spindle Motor Coolant Pump Wiring To Electrical Cabinet Speed Motor Switch Spindle Switches Control Panel Wiring Power Connection Headstock Cover Parts Headstock Controls Headstock Controls Parts List Gears Headstock Internal Gears Parts List Description Headstock Transfer Gears Gearbox Gears Gearbox Gears Parts List 291 282 283 292 323 284 285 286 Gearbox Controls Parts List Apron Front View Apron Front View Parts List Apron Apron Rear View Parts List Compound Rest & Tool Post 663 Saddle Top View Saddle Top View Parts List Saddle Bottom View Bed Stop Dial Indicator Shafts Bed Bed & Shafts Parts List Model G0740 Mfg. Since 11/12 115 Motor Main Motor Parts List 118 Model G0740 Mfg. Since 11/12 Cabinets & Panels Cabinets & Panels Parts List Tailstock Tailstock Parts List Follow Rest Electrical Cabinet & Control Panel Accessories Front Machine Labels Rear & Side Machine Labels Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty & Returns Order Hours a DAY