Framing and Clearances | Heat & Glo LifeStyle XLR-N-AU, XLR-PB-AU

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be locat- ed out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

A

A

E

10-1/4 in.

254 mm

B

C TOP VENT

ONE 90º ELBOW

D*

ALCOVE

INSTALLATION

TOP VENT

ONE 90° ELBOW

B

F

		A	B	C	D*	E	F
	Inches	53	48	75	See Section D.	19-1/4	17-3/4
					Figure 5.5 & 5.6

	Millimeters	1350	1220	1910	See Section D.	490	450
					Figure 5.5 & 5.6

Figure 5.1 Appliance Locations

Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. M • 5/12

19

Image 19

Heat & Glo LifeStyle XLR-N-AU, XLR-PB-AU manual Framing and Clearances, Selecting Appliance Location

Contents

SAI Global Ref No GSCS20139 AS4558What to do if you smell gas Models XLR-N-AU, XLR-PB-AU Homeowner Reference Information Congratulations User Guide Table of Contents Finishing Appliance SetupTroubleshooting Component Access Limited Lifetime Warranty Australian Warranty Information Other Rights Perth This warranty is void if Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Control Module Operation Nine Hour Safety Shutdown Feature Final inspection by Lighting Instructions IPIAGE 110/120 VAC or 220/240 Initial Break-in Procedure Frequently Asked QuestionsAfter Fireplace is Lit Decorative Doors Maintenance and ServiceMaintenance Tasks-Homeowner Glass Cleaning Control Compartment and Firebox Top Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Firebox Typical Appliance System Getting Started Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Front Side Finishing Detail Mantel and Wall ProjectionsMantels Combustible/Non-Combustible Mantel Leg Combustible/Non-Combustible Vent Termination Minimum Clearances Termination Locations MIN. Clearance in. mm Vent Information and Diagrams Minimum Maximum Top Vent Horizontal Termination Venting with 1 elbow Venting with 2 elbows Top Vent Horizontal Termination Exhaust restrictor Instructions Top Vent Vertical Termination No Elbows V1 Max= 44 ft .4 m V1 Minimum Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 2 elbows V1 Minimum H1 + H2 Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 3 elbows Top Vent Vertical Termination Venting with 4 elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Pipe SLP Install the Ceiling Firestop Flat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Top Vent Appliance Preparation Securing and Leveling the Appliance Installing the Optional Heat-Zone-240V Kit Assemble Vent Sections Installing Vent Pipe SLP Pipe Secure The Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Decorative Ceiling Components Assemble and Install Storm Collar Install Metal Roof Flashing Install Decorative Wall Components Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination 17 Venting through the Wall Install Horizontal Termination Cap Gas Connection Gas Information Valve Pressure Taps Access Through the Valve Assembly Optional Remote Control Receiver Location Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Accessories Requirements Junction Cord Information Electrical Service and Repair Junction Cord Information Finishing Instructions Non-Combustible Materials SpecificationFinishing Framing and Finishing Instructions Finishing Details Required Fireplace Opening Height Sealing Joints TOP View Unlimited 11 Overlap Fit Method Tonic or Martini Decorative Front Facing Material 13 Inside Fit Method Tonic Decorative Front Only Decorative Fronts Dimensions of Tonic Decorative Front Appliance Setup Media Options Air Shutter SettingVerify Performance of Appliance Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Ues to spark, and main Symptom Possible Cause Corrective Action Frequently Asked Questions/Troubleshooting Component Access Access Through the Valve Assembly Pilot Assembly Replacement Gas Valve Replacement Reference Materials Appliance Dimension Diagram Inspect Maintenance Tasks Maintenance Tasks Vent Components Diagrams SLP90- 90 Elbow 165 mm152 mm SLP-45 45 Elbow 168 mm 10-1/4 Ceiling Firestop Wall Thimble-Black Adapter Snorkel Support Box-Black15-1/2 394 mm SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP XLR-N-AU, XLR-PB-AU Service Parts #14 Valve Assembly XLR-N-AU, XLR-PB-AU Service Parts List Contact Information