Heat & Glo LifeStyle XLR-PB-AU, XLR-N-AU manual

Top Vent - Vertical Termination

Venting with 4 elbows

Note: Use SLP Series components only.

V1 Min.	H1 Max.	V2 Min.	H2 Max.	V3 Min.

1-1/2 ft. (457 mm)	4 ft. (1.2 m)	4 ft. (1.2 m)	4 ft. (1.2 m)	3 ft. (1.0 m)

	V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)

V3

V2

H2

H1

V1

Figure 7.10

30	Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. M • 5/12

Image 30

Heat & Glo LifeStyle XLR-PB-AU, XLR-N-AU manual Top Vent Vertical Termination Venting with 4 elbows

Contents

Ref No GSCS20139 AS4558 SAI GlobalWhat to do if you smell gas Models XLR-N-AU, XLR-PB-AU Congratulations Homeowner Reference Information Table of Contents User Guide Component Access Appliance SetupTroubleshooting Finishing Australian Warranty Information Limited Lifetime Warranty Other Rights This warranty is void if Perth Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Decorative Doors and Fronts Nine Hour Safety Shutdown Feature Control Module Operation Lighting Instructions IPI Final inspection byAGE 110/120 VAC or 220/240 Frequently Asked Questions Initial Break-in ProcedureAfter Fireplace is Lit Glass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Decorative Doors Firebox Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Control Compartment and Firebox Top Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Mantel Leg Combustible/Non-Combustible Mantel and Wall ProjectionsMantels Combustible/Non-Combustible Front Side Finishing Detail Termination Locations Vent Termination Minimum Clearances MIN. Clearance in. mm Vent Information and Diagrams Top Vent Horizontal Termination Venting with 1 elbow Minimum Maximum Top Vent Horizontal Termination Venting with 2 elbows Top Vent Vertical Termination No Elbows V1 Max= 44 ft .4 m Exhaust restrictor Instructions Top Vent Vertical Termination Venting with 2 elbows V1 Minimum Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 3 elbows V1 Minimum H1 + H2 Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 4 elbows Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Pipe SLP Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Top Vent Installing the Optional Heat-Zone-240V Kit Securing and Leveling the Appliance Installing Vent Pipe SLP Pipe Assemble Vent Sections Assemble Slip Sections Secure The Vent Sections Install Decorative Ceiling Components Disassemble Vent Sections Install Metal Roof Flashing Assemble and Install Storm Collar Install Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap 17 Venting through the Wall Gas Information Gas Connection Access Through the Valve Assembly Valve Pressure Taps Optional Accessories Requirements Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Remote Control Receiver Location Electrical Service and Repair Junction Cord Information Junction Cord Information Framing and Finishing Instructions Non-Combustible Materials SpecificationFinishing Finishing Instructions Finishing Details Sealing Joints Required Fireplace Opening Height TOP View Unlimited Facing Material 11 Overlap Fit Method Tonic or Martini Decorative Front 13 Inside Fit Method Tonic Decorative Front Only Dimensions of Tonic Decorative Front Decorative Fronts Appliance Setup Air Shutter Setting Media OptionsVerify Performance of Appliance Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Ues to spark, and main Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Component Access Access Through the Valve Assembly Gas Valve Replacement Pilot Assembly Replacement Appliance Dimension Diagram Reference Materials Maintenance Tasks Inspect Maintenance Tasks Vent Components Diagrams SLP-45 45 Elbow 168 mm 10-1/4 165 mm152 mm SLP90- 90 Elbow Snorkel Support Box-Black Ceiling Firestop Wall Thimble-Black Adapter15-1/2 394 mm SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP Service Parts XLR-N-AU, XLR-PB-AU #14 Valve Assembly Service Parts List XLR-N-AU, XLR-PB-AU Contact Information