Honeywell 4800dr TTL-232 Baud Rate

2 - 4

Control + ASCII Mode On: The document reader sends key combinations for ASCII control characters

for values 00-1F. Refer to Keyboard Function Relationships, page 8-1 for CTRL+ ASCII Values.

Default

= Off.

Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad.

Default = Off.

TTL-232 Baud Rate

Baud Rate sends the data from the document reader to the terminal at the specified rate. The host ter-

minal must be set for the same baud rate as the document reader.

Default = 115,200.

Control + ASCII Mode On

* Control + ASCII Mode Off

Numeric Keypad Mode On

* Numeric Keypad Mode Off

300

2400

600

1200

4800

38400

9600

19200

* 115,200

57,600

Contents

Main Disclaimer Table of Contents Chapter 1 - Getting Started Chapter 2 - Terminal Interfaces Chapter 3 - Output Chapter 4 - Data Editing Chapter 5 - Data Formatting Chapter 6 - Symbologies Page Chapter 7 - OCR Programming Chapter 8 - Interface Keys Chapter 9 - Utilities Chapter 10 - Serial Programming Commands Chapter 11 - Product Specifications Sample Symbols Chapter 12 - Maintenance Chapter 13 - Customer Support Page Getting Started About This Manual Unpacking the Document Reader Document Reader Models Connecting the Document Reader with USB Connecting the Document Reader with TTL-232 Serial Port Supported Terminals Programming the Interface - Plug and Play USB Connection IBM SurePos Note: After scanning one of these codes, you must power cycle the cash register. USB PC or Macintosh Keyboard USB HID USB COM Port Emulation Note: No extra configuration (e.g., baud rate) is necessary. TTL-232 Serial Port Connection Aligning the Document Reader Tray Reading Techniques Using the Imager Out of the Stand 2 - 1 Terminal Interfaces Keyboard Country Keyboard Country (continued) Keyboard Style Default = Regular. Keyboard Modifiers Default = Off. TTL-232 Baud Rate Default = 115,200. RS-232 Word Length: Data Bits, Stop Bits, and Parity Default = 8. Default = 1. Default = None. TTL-232 Receiver Time-Out Page Output Good Read Indicators Beeper Good Read Beeper Volume Good Read Beeper Pitch Good Read Beeper Duration Good Read Default = Normal. LED Good Read LED Indicator State Default = LED Indicator Off. Good Read Delay Default = No Delay. User-Specified Good Read Delay Trig ger Mode s Manual/Serial Trigger Scan Stand Mode Scan Stand Symbol Presentation Mode Presentation Sensitivity Default = 1. Hands Free Time-Out Default = 5,000 ms. Reread Delay User-Specified Reread Delay LED Power Level Imager Time-Out Aimer Delay User-Specified Aimer Delay Aimer Mode . Default = Interlaced. Centering Default Centering = 40% for Top and Left, 60% for Bot- tom and Right. Decode Window Decode Win- dow On, Decode Window X at 68%, Decode Window Y at 60% Decode Search Mode Preferred Symbology High Priority Symbology Default = None Low Priority Symbology Default = None Preferred Symbology Time-out Output Sequence Overview Require Output Sequence Note:This selection is unavailable when Multiple Symbols (page 3-14) is enabled. Output Sequence Editor Output Sequence Examples Note:Code 93 must be enabled to use this example. Output Sequence Editor Require Output Sequence Note: This selection is unavailable when the Multiple Symbols Selection is turned on. Multiple Symbols No Read Print Weight Default = 4 Video Reverse Working Orientation Default = Upright. Data Editing Prefix/Suffix Overview Default prefix = None. Default suffix = None Points to Keep In Mind To Add a Prefix or Suffix: To Clear One or All Prefixes or Suffixes: To Add a Carriage Return Suffix to all Symbologies Prefix Selections Suffix Selections Function Code Transmit Default = Enable. Intercharacter, Interfunction, and Intermessage Delays Intercharacter Delay Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay Interfunction Delay Intermessage Delay Page Data Formatting Data Format Editor Introduction Default Data Format setting = None. To Add a Data Format Note: The wildcard for all terminal types is 099. Other Programming Selections Data Format Editor Commands Syntax = F2nnxx Syntax = F1xx Send Commands Page Data Format Editor Data Formatter Default = Data Formatter On, but Not Required. Alternate Data Formats Page Page Symbologies All Symbologies Message Length Description Codabar <Default All Codabar Settings> Codabar Codabar Start/Stop Characters Codabar Concatenation Default = On. Codabar Message Length Code 39 < Default All Code 39 Settings > Code 39 Code 39 Start/Stop Characters Dont Transmit. Code 39 Check Character Default = No Check Character. Code 39 Message Length Code 39 Append Code 32 Pharmaceutical (PARAF) Note: Trioptic Code (page 6-25) must be turned off while scanning Code 32 Pharmaceutical codes. Full ASCII Default = Off Code 39 Code Page Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 Check Digit Default = No Check Digit. Interleaved 2 of 5 Message Length Code 93 < Default All Code 93 Settings > Code 93 Code 93 Message Length Code 93 Code Page Page Page Page Check Digits Required Default = Two Check Digits. Code 11 Message Length Code 128 <Default All Code 128 Settings> Code 128 ISBT 128 Concatenation Default =Off. Code 128 Message Length Code 128 Code Page Tele pen <Default All Telepen Settings> Tele pen Telepen Output Default = AIM Telepen Output. Telepen Message Length UPC-A UPC-A Check Digit UPC-A Number System UPC-A Addenda UPC-A Addenda Required UPC-A/EAN-13 with Extended Coupon Code UPC-E0 UPC-E0 UPC-E0 Expand UPC-E0 Addenda Required UPC-E0 Addenda Separator UPC-E1 EAN/JAN-13 EAN/JAN-13 Check Digit EAN/JAN-13 Addenda EAN/JAN-13 Addenda Required EAN/JAN-13 Addenda Separator ISBN Translate EAN/JAN-8 EAN/JAN-8 Check Digit EAN/JAN-8 Addenda EAN/JAN-8 Addenda Required Default = Not Required. MSI <Default All MSI Settings> MSI MSI Check Character Default = Validate Type 10, but Dont Transmit. MSI Message Length Plessey Code <Default All Plessey Code Settings> Plessey Code Plessey Message Length Page PosiCode <Default All PosiCode Settings> PosiCode A and B PosiCode Message Length Trioptic Code Codablock F <Default All Codablock F Settings> Codablock F Codablock F Message Length Page Page Page MicroPDF417 Message Length EANUCC Composite Codes UPC/EAN Version EANUCC Composite Code Message Length EAN Default = EANUCC Emulation Off UCC Emulation TCIF Linked Code 39 (TLC39) Default = O ff. Page Page Page Page QR Code QR Code Message Length Data Matrix < Default All Data Matrix Settings > Data Matrix Data Matrix Message Length MaxiCode < Default All MaxiCode Settings > MaxiCode MaxiCode Message Length Aztec Code < Default All Aztec Code Settings > Aztec Code Page Page OCR Programming Note: Setting the template and check character options are essential for OCR reading. OCR Fonts < Default All OCR Settings > OCR OCR Templates Creating an OCR Template Template Characters Note: OCR templates default to eight digits, no check character. To Add an OCR Template 551ABC983 Stringing Together Multiple Formats (Creating Or Statements) 99028650 9902XZ50 OCR User-Defined Variables 654321ABC 654321BAC 654321CCC Reading Multi-Row OCR OCR Check Character 01234569 OCR Modulo 10 Check Character OCR Modulo 36 Check Character OCR User-Defined Check Character 6512351X Programming a User-Defined Check Character Weighting Options 3-1-3-1 Weighted Modulo 10 Check Character 2-1-2-1 Weighted Modulo 10 Check Character OCR ISBN Application Example OCR Template Codes Exit Selections 8 - 1 Interface Keys Keyboard Function Relationships Supported Interface Keys 8 - 2 Utilities Show Data Format Resetting the Standard Product Defaults Test Menu Note: This feature should not be used during normal document reader operation. 2D PQA (Print Quality Assessment) Visual Xpress Introduction Visual Xpress Operations Installing Visual Xpress from the Web Temporary Visual Xpress Configuration Serial Programming Commands Conventions option parameter Menu Command Syntax Concatenation of Multiple Commands Responses Examples of Query Commands Example #1: What is the range of possible values for Codabar Coding Enable? Example #2: What is the default value for Codabar Coding Enable? Trigger Commands Resetting the Standard Product Defaults 10 - 4 Menu Commands Note: Not all menu commands apply to all document reader models. Terminal Interfaces 10 - 5 Output Selections 10 - 6 10 - 7 10 - 8 Prefix/Suffix Selections Data Formatter Selections Symbologies 10 - 9 10 - 10 10 - 11 10 - 12 10 - 13 10 - 14 10 - 15 10 - 16 OCR Selections 11 - 1 Product Specifications Parameter Specification 11 - 2 11 - 3 Standard Cable Pinouts Serial Output USB Page Maintenance Repairs Maintenance Cleaning the Document Reader Inspecting Cords and Connectors Troubleshooting Is the power on? Is the white scanning illumination on when the imagers button is pressed? Is the document reader having trouble reading your barcodes? Is the barcode displayed but not entered? Does the document reader read the barcode incorrectly? The document reader wont read your barcode at all. Page Customer Support Technical Assistance Online Technical Assistance Product Service and Repair E-mail: naservice@honeywell.com Limited Warranty Page Page A Appendix A All Symbologies m Symbology Chart m ASCII Conversion Chart (Code Page 1252 A - 3 ) Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char Code Page Mapping of Printed Barcodes Note: The Code Page option is available for Code 39, Code 93, and Code 128. Page Page Page Page Sample Symbols OCR Programming Chart Page Page Programming Chart