Honeywell LYNXR-EN Follow Me Reminder Phone Number, Phone System Select, Split/Dual Reporting

Data Field Descriptions

Field 46: Enter up to 24 digits. Do not fill unused spaces. Enter 0-9, #+11 for ‘*’; #+12 for’#’; #+13 for a pause (2 seconds).

✻46	“Follow Me Reminder” Phone Number							This option allows the user to schedule a time driven message. When
	Enter up to 24 digits.							activated the system will dial the phone number programmed and deliver a
								voice message (custom words 72, 73 and 74). This option is only supported
								when the pager or follow me feature is enabled in field ✻49 (option 6-9 or
								10-13).
								If using the Follow Me Reminder feature, enter the phone number here. If
								fewer than 24 digits are entered, exit by pressing [✻]. To clear entries from
								the field press ✻46✻.
								The telephone message can be terminated (acknowledged) by pressing any
								key on the telephone keypad. Pressing any key on the local LYNXR keypad
								will terminate (acknowledge) both the follow me and the local reminder
								announcements.
								Note: The follow me reminder announcement will be terminated if any
									other event requires the system to dial out or if and audible alarm
									has occurred.
✻47	Phone System Select							This option is used to enter the correct type of phone dialing (pulse or tone),
	Note: For LYNXR/LYNXR24 only options 0, 1, 2, and 3							and to select the correct WATS line option for the Central Station. For
								LYNXR-EN this option is used to activate the speaker phone option.
		are applicable. For LYNXR-EN all options apply.
		Central		Dialing Mode				Note: If using pulse dialing, you must enter the numbers slowly in order to
		Station	Pulse	Tone		Pulse	Tone		allow the pulse dialer time to operate.
		No WATS	0 = No	1 = No		4 = With	5 = With
			Speaker	Speaker		Speaker	Speaker
			Phone	Phone		Phone	Phone
		WATS	2 = No	3 = No		6 = With	7 = With
			Speaker	Speaker		Speaker	Speaker
			Phone	Phone		Phone	Phone
✻48	Report Format for Primary/Secondary							Enter ✻ as the 4th digit of ✻43 through ✻44, if 3+1 dialer reporting is to be
	Primary			Secondary				used. (For an explanation of these formats, see the System Communication
								section of this manual.)
	See choices below			See choices below				Notes: (1)		The maximum number of alarm and alarm restore reports
	0 = 3+1; 4+1 ADEMCO Low Speed Standard									during one armed period is determined by field ✻92.
	1 = 3+1; 4+1 Radionics Standard								(2) If Option 5 is selected a 10-digit account number must be
	2 = 4+2 ADEMCO Low Speed Standard								(3)	entered in Fields ✻43 or ✻44.
	3 = 4+2 Radionics Standard									Option 5 or 7 (ADEMCO Contact ID® Reporting) must be
										selected for AVM.
	5 = ADEMCO Contact ID® Reporting with 10-digit
									(4)	Option 5 or 7 (ADEMCO Contact ID® Reporting) must be
		subscriber account number
										selected if installing the 5842 Wireless Dialer.
	6 = 4+2 ADEMCO Express
	7 = ADEMCO Contact ID® Reporting with 7-digit
		subscriber account number
	8 = 3+1; 4+1 ADEMCO Low Speed Expanded
	9 = 3+1; 4+1 Radionics Expanded
✻49	Split/Dual Reporting							This field is used to select a reporting option as follows:
								Enter:	0 - 5 when reporting to telephone receivers.
		To Primary			To Secondary				6 - 9 when reporting to a pager is desired.
	0 = All reports				None, unless primary				10 - 13 when reporting to an auxiliary telephone receiver.
					fails, then all			Pager Report Format
	1 = Alarms, Restore, Cancel				Others
								Options 6-9 send reports to the primary phone number, in a format defined
	2 = All except Open/Close, Test				Open/Close, Test
								in Field ✻48, and send reports to a pager, which has its phone number
	3 = Alarms, Restore, Cancel				All
								entered as the secondary phone number in Field ✻42. The pager report is a
	4 = All except Open/Close, Test				All
								7-digit code, with optional 16-digit prefix, in the following format:
	5 = All reports				All
								AAAAAAAAAAAAAAAA-EEE–00NN where:
		To Primary			To Paging Number
								AAA = Optional 16 digits for PIN number, etc. See Field ✻88 for full
					Alarms, Open/Close ‡,
	6 = All reports except Open/Close								description of these characters.
					Troubles			EEE = 3-digit Event Code as follows:
	7 = All reports				Alarms, Troubles			911 = Alarm (NN = zone number)
	8 = All reports				Alarms, Open/Close ‡,			101 = Open, system disarmed (NN = user no.)
					Troubles			102 = Close, system armed (NN = user no.)
	9 = All reports except Open/Close				Open/Close ‡			811 = Trouble (NN = zone no.)
								00 =	Always displayed before 2-digit user/zone no.
								NN = 2-digit user number or zone number, depending on the type of
		To Primary			To Follow Me System
									event (EEE) that occurred. NN=00 indicates AC loss, system low
					Phone Number				battery, or low battery in 5827.
	10=All reports except Open/Close				Alarms, Open/Close ‡,
								Follow Me System Report Format
					Troubles			Options 10-13 send reports to the primary phone number, in a format
	11 = All reports				Alarms, Troubles			defined in Field ✻48, and sends voice message to the secondary phone
	12=All reports				Alarms, Open/Close ‡,			number entered in Field ✻42.
					Troubles			The message is a repeatable system status announcement. If the manual
	13=All reports except Open/Close				Open/Close ‡			paging option has been programmed in Field ✻87, the message will repeat
								“system, system…..”.
	‡ Will report Users 0, 5-8, and, if using wireless button-type
								The message can be terminated by pressing any key on the telephone
	devices, will report the zone number of the arm or disarm
								keypad.
	button 26-33. All other zones and users are not reported.

–19–