✻56 Enhanced Zone Programming Mode
|
|
|
|
|
| RF Learning - Two (2) transmissions (2 key depressions) at least 5 |
|
|
|
|
|
| seconds apart will be required for BR type devices (device type 5). Two |
|
|
|
|
|
| beeps will sound after the second transmission, confirming that the loop |
|
|
|
|
|
| number and serial number have been learned. |
|
|
|
|
|
| For all other device types, four (4) transmissions are required (fault, |
|
|
|
|
|
| restore and fault, restore). A single beep will sound after the second |
|
|
|
|
|
| transmission confirming that the loop and serial number have been |
|
|
|
|
|
| captured. Following the fourth transmission the system will confirm that |
|
|
|
|
|
| the loop number and serial number have been learned and announce the |
|
|
|
|
|
| Voice Descriptor for the zone, if it is programmed, followed by two beeps. |
|
|
|
|
|
| Press [✻] to continue. |
|
|
|
|
|
| Manual Entry - Enter the desired loop number and press [✻] to |
|
|
|
|
|
| continue (see the transmitter’s Installation Instructions for specific loop |
|
|
|
|
|
| designations). |
|
|
|
|
|
| Note: The loop number can be changed even if the zone has already |
|
|
|
|
|
| been entered. Care should be taken when using this feature as it |
|
|
|
|
|
| has the capability to make zones inoperable by creating a |
|
|
|
|
|
| mismatch of a working serial number/loop number combination. |
|
|
|
|
|
| This should be |
|
|
|
|
|
| “L” indicates that the zone’s serial number has already been enrolled. |
|
|
|
|
|
|
|
|
|
|
|
| Delete zone parameters | This function deletes either the serial number or all zone information |
| F |
|
|
| confirmation | that is programmed for the zone. |
|
|
|
| If “00” was entered in the zone type, the confirmation of the delete | ||
|
|
|
| 0 = discard the delete request | ||
|
|
|
| request will delete all information associated with the zone currently | ||
|
|
|
|
| 1 = confirm requested delete | being programmed. |
|
|
|
|
| Note: If 00 was entered as a zone type in prompt | If “0” was entered in the loop number, the confirmation of the delete |
|
|
|
|
| (b), 00 will be retained and system will | request will delete the serial number of to the zone currently being |
|
|
|
|
| advance to prompt (1C) | programmed. |
|
|
|
|
|
|
|
|
|
|
|
| Enroll mode | If “L” is displayed, the serial number for this transmitter has already |
| IA | LC |
|
| 0 = advance to the VOICE DESCRIPTOR | been entered. It may, however, still be viewed, confirmed (only if in |
|
|
| listen mode), or deleted. | |||
|
|
| prompt (1C). | |||
|
|
|
| |||
|
|
|
|
| Note: This will save all zone parameters. | View serial number |
|
|
|
|
| 1 = enter now and proceed to SERIAL | |
|
|
|
|
| Enter “3”. Each digit will be redisplayed, and the keypad will beep once | |
|
|
|
|
| NUMBER prompt (1b). | for digits |
|
|
|
|
| Note: Not applicable if the serial number is |
|
|
|
|
|
| already present. | Confirm serial number |
|
|
|
|
| 2 = copy the last serial number entered into | The serial number/loop number combination can be confirmed after one |
|
|
|
|
| transmission from a BR type device or two transmissions (fault and | |
|
|
|
|
| local ram. | |
|
|
|
|
| restore) from a UR or RF type device. If a transmission is received that | |
|
|
|
|
| Note: If this is the 1st zone, none will be in the | |
|
|
|
|
| matches the serial number and loop number entered, the system will | |
|
|
|
|
| buffer and the panel will emit a long tone. | confirm the reception by announcing the Voice Descriptor for the zone, if |
|
|
|
|
| Not valid if serial number is already present. | it is programmed, followed by three beeps, and a “C” will appear on the |
|
|
|
|
| 3 = view existing serial number. | display indicating the received serial number and loop number have |
|
|
|
|
| Note: Only if “L” is displayed. If “L” is not | been confirmed. No further transmissions will be received. |
|
|
|
|
| displayed, panel will emit a long beep. | Delete serial number |
|
|
|
|
| 9 = advance to F; delete existing serial | |
|
|
|
|
| The serial number can be deleted by entering “9”. | |
|
|
|
|
| number. | |
|
|
|
|
|
| |
|
|
|
|
| Note: Only if “L” is displayed. If “L” is not | If “L” is not displayed, the serial number for this transmitter has not |
|
|
|
|
| displayed, panel will emit a long beep. | |
|
|
|
|
| been previously entered. You may enter the serial number manually, | |
|
|
|
|
| [✻] = advance to the VOICE DESCRIPTOR | |
|
|
|
|
| copy the previous serial number, return to Prompt (E) or enter the serial | |
|
|
|
|
| prompt (1C). This will save all zone | number later using the ✻83 Enhanced Sequential Mode. |
|
|
|
|
| parameters. |
|
|
|
|
|
| [#] = return to the LOOP NUMBER prompt |
|
|
|
|
|
| (E). |
|
|
|
|
|
| Note: In order for all entered parameters to be |
|
|
|
|
|
| accepted, you must advance to the VOICE |
|
|
|
|
|
| DESCRIPTOR prompt (1C). |
|
|
|
|
|
|
|
|