Honeywell LYNXR Series, LYNXR-EN setup guide Zone number, Zone type, Report code, Input type

✻56 Enhanced Zone Programming Mode

While in Program mode, press ✻56 to enter Zone Programming Menu Mode. Refer to the zone assignment table for ✻56 on the separate programming form.

The following explains the ✻56 prompts in detail. The left two columns identify the prompts and list the available entries for each. The right-most column provides a further explanation of the entries.

Note: You may find it convenient to adjust the volume setting before entering the Programming Mode. This will allow you to clearly hear feedback announcements or system beeps.

			Zone number	Enter the 2-digit zone number to be programmed and the Voice Descriptor
A		0I	01-41, 95, 96, 99 = Zone number	for the selected zone number will be announced, if it is programmed. Press
				[✻] to advance.
			[✻] = continue
				• Zone 01 = hardwire
			00 = exit Zone Programming mode
				• Zones 02-25 = RF zones (only)
				• Zones 26-41 = Button zones (only)
				• Zone 92 = Duress
				• Zones 95, 96, 99 = Panic zones
				Pressing 00 exits mode, upon which the prompt “56” blinks, indicating the
				mode is inactive. Press [✻] + any field number to go to that field.
			Zone type	Each zone must be assigned to a zone type, which defines the way in
	b	zt	00-24 = zone type	which the system responds to faults in that zone. Enter the 2-digit zone
				type for this zone as follows:
			[✻] = continue
				00 = Not Used	08 = 24 Hr Aux
			[#] = return to previous prompt
				01 = Entry/Exit #1	09 = Fire without verify
			Note: If 00 is accepted as a zone type, save the 00	02 = Entry/Exit #2	10 = Interior w/Delay
				03 = Perimeter	20 = Arm–Stay
			zone type and advance to the confirm delete	04 = Interior Follower	21 = Arm–Away
			prompt (F).	05 = Trouble Day/Alarm Night	22 = Disarm
				06 = 24 Hr Silent	23 = No Alarm Response
				07 = 24 Hr Audible	24 = Silent Burglary
			Report code	The report code consists of 2 hexadecimal digits, each in turn consisting of
	C	rc	Enter the report code for this zone.	2 numerical digits. For example, for a report code of "3C", enter [0][3] for
				"3" and [1][2] for "C".
			[✻] = continue
				If this is Zone 1, 95, 96 or 99, the system skips to the VOICE
			[#] = return to previous prompt
				DESCRIPTOR prompt (1C).
			Input type	Enter the input type for the transmitter assigned to this zone. Refer to the
	d	i	3 =RF (supervised RF) – sends periodic	transmitter’s instructions for input types of each transmitter.
			check-in signals, faults, restore and low	Note: Zones 2-25 should be assigned Input Type 3 or 4 . Zones 26-41
			battery signals
				should be assigned Input Type 5 only.
			Note: RF type transmitters must remain within
			range of the receiver, otherwise a
			supervision failure signal will occur.
			4 = UR (unsupervised RF) – sends same as
			“RF” type, but control does not supervise
			the check-in signals
			5 = BR (button type) – sends only fault and low
			battery signals; does not send restores or
			check-in signals
			Note UR and BR type transmitters may be carried
			off premises (out of range without causing a
			supervision failure.
			[✻] = continue
			[#] = return to previous prompt
			Loop number or Loop and Serial	This prompt can be used to enroll loop number and serial number via RF
	E
		l	number (if using RF Learning)	transmission or the loop number can be enrolled manually. If using the
				RF Learning Mode, there is no need to manually enter a loop number.
			1-4 = loop number for the zone of the
				Proceed directly to RF Learning
			transmitter being entered.
			0 + [✻] = continue to DELETE ZONE	Notes: (1) BR type devices cannot be enrolled by using UR or RF type.
			PARAMETERS CONFIRMATION	Likewise, UR or RF type devices cannot be enrolled by using a
			prompt (F)	BR type device. There is a 52-second time-out for RF
			[✻] = continue to the ENROLL MODE prompt	enrolling. At the end of the time-out, the system returns to
			(1A) if not entered, or VOICE	the INPUT TYPE prompt (d). If enrolled, loop number and “L”
				are displayed.
			DESCRIPTOR prompt if already entered
				(2) Once encrypted (high-security) devices have been enrolled they
			[#] = return to previous prompt
				must be activated. Refer to the device’s Installation
				Instructions to activate the High-Security Mode.

–28–