Honeywell LYNXR Series Data Field Descriptions, SecondDialer Delay Burglary, Periodic Test Report

Data Field Descriptions

✻50	15-Second Dialer Delay (Burglary)			If enabled, provides communication delay to the central station and allows
	0	= no dialer delay		the subscriber time to avoid a false alarm transmission. Delay does not
				apply to zone type 6, 7, 8, and 9 alarms, which are always sent as soon as
	1	= provide 15-second delay of burglary alarm report
				they occur. UL installations: must be 0 (no delay)
	when armed away
✻51	Periodic Test Report			Test report code entered in field ✻64 is sent.
	0	= no test report	2 = weekly
	1	= once every 24 hrs	3 = once every 30 days
✻52	First test Report Offset			This is the time to first report from programming or downloading.
	0	= 24 hrs after exit program mode or download
	1	= 6 hours after exit program mode or download
	2	= 12 hrs after exit program mode or download
	3	= 18 hrs after exit program mode or download
✻53	Sescoa/Radionics Select			Select 0 for all other formats.
	0	= Radionics (0–9, B–F reporting)
	1	= SESCOA (0–9 only reporting)
✻54	Lack of Usage Notification			If enabled, notifies the central station if an end user is not operating their
	0	= Disabled	4 = 90 days	security system by sending a System Inactivity report 654. The report will
				be sent only to the Primary phone number and only if Contact ID® format
	1	= 1 day	5 = 180 days
				was selected.
	2	= 7 days	6 = 365 days
				Note: The report will follow the ✻49 = 0 rules, no matter which selection
	3	= 27 days		was made in ✻49.
	Note: There will be no local annunciation indicating that
		this report has been sent to the Central Station.
✻58	RF Jam Detection			For Event Logging, Option 2 must be selected.
	0	= no jam detection		If the control detects an RF jam condition, a “FAULT” message appears for
	1	= RF jam detection with event logging, but no		zone 90. The Contact ID® code for RF Jam is 344.
		central station report		Note: This feature cannot be used in conjunction with the 5827 wireless
	2	= RF jam detection with event logging and with		keypad.
		central station report (if trouble/restore report is
		enabled in fields ✻60, ✻71)

SYSTEM STATUS AND RESTORE REPORT CODES PROGRAMMING (✻59 – ✻76, & ✻89)

Program Report Codes using the interactive ✻56 Enhanced Zone Programming Mode, or codes can be entered in data fields ✻59-✻76, ✻89. The following is a set of guidelines when programming report codes. The actual report code digits that you enter depend upon the particular installation, and should be in agreement with you and the central station office receiving the signals.

With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, A, B, C, D, E, or F. Enter "#+10" for A (reports a “0” on some receivers), "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. Entering "0" in the first box will disable a report. Entering "0" in the second box results in automatic advance to the next field.

With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, or A–F, as described above. Entering "0" in the first box will disable a report. Entering "0" in the second box will eliminate the expanded message for that report.

With ADEMCO Contact ID® Reporting: Enter a digit in the first box to enable the zone to report. Use a different digit for each zone until you have used up available digits. If the number of zones exceeds the number of available digits, begin with digit 1 again. This is an "enabling" code only and is not the actual code sent to the central station office. Entries in the second boxes will be ignored. For system status (non-alarm) codes, enter a “1” in the first box for all the system conditions you want to send to the central station. A "0" in the first box disables the report.

–20–