Honeywell LYNXR-EN setup guide Device Programming Menu Mode, Powerline Carrier Device, programming

✻80 Device Programming Menu Mode

The following explains these prompts in detail. The left two columns identify the prompts and list the available entries. The right-most column provides a further explanation of the entries.

Note: Entering a number other than one specified will give unpredictable results.

		Powerline Carrier Device		Entering “1” advances to the next prompt below.
	80	programming		Entering “0” exits mode, upon which this prompt blinks, indicating the
				mode is inactive.
		0 = exit mode
		1 = enter mode
		Device number		Enter device numbers as 2-digit entries.
A	0I
		01-08 = device number to be programmed
		[✻] = continue
		00 = exit Device Programming mode
		Device action		Enter the 1-digit action (0-3) for the device being programmed (current
b
	aa	0 = No response		action is displayed).
				NOTES:
		1 = Close for 2 seconds
		2 = Close and Stay Closed		1. If “3” is entered (pulse), only up to 3 different devices can be pulsed
				if one of the devices is a siren/horn (X-10 Powerhouse Security
		3 = Continuous Pulse on & off (1 sec ON, 1 sec
				model SH10A). In addition, the siren/horn cannot be manually
		OFF)		activated using the lights on/lights off keypad commands.
		[✻] = continue		2. If using an X-10 Powerhouse Security SH10A siren:
		[#] = return to previous prompt		• you must use device action “3.”
				• you must change the device action default to “3” if using default
				table 2 or 4
		Start event type		Enter the 1-digit event type (0-3) to activate the device being
C	et	0 = Not used	3 = Trouble	programmed. A zone list must be used in conjunction with an event. If
				a zone type/system operation is to be used instead of an event, enter
		1 = Alarm	[✻] = continue
		2 = Fault	[#] = return to previous	“0”.
			prompt
		Start zone list		If a zone list will be used to start the device action, enter the zone list
d
	zl	1-3 = zone list number (to be programmed in		number at this prompt.
		field ✻81)
		0 = zone list not used for this device
		[✻] = continue
		[#] = return to previous prompt
		Start zone type		If a zone type or system operation will be used to start the device
E
	zt	01-58 = zone type to start this device action		action, enter the appropriate 2-digit code for the device being
		(select only those that are applicable)		programmed (see table that follows).
		00 = zone type not used for this device			Choices for zone types
		[✻] = continue		00 = Not Used	04 = Interior Follower		08 = 24 Hr Aux
		[#] = return to previous prompt		01 = Entry/Exit #1	05 = Trouble Day/Alarm Night 09 = Fire
				02 = Entry/Exit #2	06 = 24 Hr Silent		10 = Interior w/Delay
				03 = Perimeter	07 = 24 Hr Audible		24 = Silent Burglary
				Choices for system operation
				20 = Arming–Stay	33 = Any Alarm (except zt 08)		42 = Sys. Batt. Low
				21 = Arming–Away	36 = At Bell Timeout**		43 = Comm. Failure
				22 = Disarm. (Code + OFF)		38 = Chime	52 = Kissoff
				31 = End of Exit Time	39 = Any Fire Alarm		58 = Duress
				32 = Start of Entry Time		40 = Bypassing
				** Or at Disarming (which ever occurs earlier)
				Note: If an X-10 device has been programmed to ZT05 or ZT07 and *55
				has been enabled, the device response will be dependent upon the
				selection made in *55 Field "Ln".
		Stop zone list		If a zone list will be used to STOP, or restore, the device action, enter
F	zl	1-3 = zone list to stop this device action		the zone list number 1, 2, or 3 (to be programmed in ✻81 mode). If not
				used, enter “0”.
		0 = zone list not used
		[✻] = continue
		[#] = return to previous prompt
		Stop zone type		If a zone type or system operation will be used to STOP the device
IA	zt	01-58 = zone type to start this device action		action, enter the appropriate 2-digit code (see the "ZT" choices listed
				above). If not, enter 00.
		(select only those that are applicable)
		00 = zone type not used for this device		The display then returns to the DEVICE NUMBER prompt (A) so that
				you can enter the next device number to be programmed, or enter [0][0]
		[✻] = continue
				to end device programming.
		[#] = return to previous prompt

–33–