Honeywell LYNXR Series Troubleshooting Guide, S Y S T E M i n c l u d i n g W i r e l e s s

Troubleshooting Guide

S Y S T E M ( i n c l u d i n g W i r e l e s s )

	SYMPTOM		POSSIBLE CAUSE		REMEDY
1.	Transmitter signal	1a.	Transmitter not properly powered.	1a	Check or change transmitter's battery.
	not received at	1b.	If Transmitter is 5827, House Code not	1b.	Check code switches inside transmitter.
	control.		set in field ✻24, or transmitter is not set		Must match with RF House Code
			to same House Code set in that field.		programmed.
		1c.	Transmitter is located too far from RF
			receiver.	1c.	Move transmitter or RF receiver.
		1d.	There is metal shielding between	1d.	Check for large metal obstructions, then
			transmitter and RF receiver.		relocate transmitter if necessary.
		1e.	Transmitter is malfunctioning.	1e.	Verify by activating control with
					another, similar transmitter. If O.K.
		1f.	Transmitter No. (zone) is not		now, return defective transmitter.
			programmed.	1f.	Verify programming.
2.	Transmitter zone	2a.	Transmitter zone type (ZT) is set to 00	2a.	Set ZT to a valid active zone type in
	number appears		(Not Used).		field ✻56.
	during Transmitter	2b.	Transmitter battery not installed.	2b.	Install proper battery.
	Sniffer mode, but	2c.	5800 System transmitter not "entered" in
	does not clear.			2c.	"Enter" unit in field ✻56 or ✻83.
			system.
3.	Low battery message
	on keypad.
3a.	"Low Bat" (no zone Nos.)	3a.	System battery is low or missing.	3a.	Replace system battery.
3b.	"Low Bat" + "00".	3b.	Remote RF keypad/button battery is low.	3b.	Replace battery in the RF keypad.
3c.	"Low Bat" + "nn".	3c.	Transmitter for zone “nn” has a low	3c.	Replace the battery in the displayed
			battery.		transmitter.
4.	Periodic beep(s) from	4a.	System is in Test mode.	4a.	Enter Code + OFF to exit Test mode.
	keypad.	4b.	A transmitter low battery has occurred	4b.	Enter Code + OFF and replace the
			and is displayed.		battery.
		4c.	A supervision fault has occurred.	4c.	Check the transmitter indicated.
					Restore communication to the receiver
		4d.	System low battery		to cancel the condition.
				4d.	Replace system battery
5.	With 5800 System,	Put control in Test mode. If zone does not
	there is no response	respond, try operating the tamper switch or
	to a transmitter in	another input to the transmitter.
	normal operation,	5a.	If another input causes the zone to be	5a.	Delete input's serial number (not the
	although zone		displayed, the wrong input was "entered"		zone), and enter the proper input (see
	number clears during		when programming.		field ✻56).
	Transmitter Sniffer	5b.	If no response at all from this
	mode.			5b.	Determine which transmitter is
			transmitter, this physical transmitter
			has not been entered by the system.		programmed for this zone and
			Transmitter Sniffer display is being		reprogram as necessary.
			cleared by another unit programmed for
			this zone.
6.	Nuisance or phantom	6a.	Sensors not properly installed, wired, or	6a.	Check installation to see if in
	alarm.		monitored.		accordance with established procedure.
		6b.	Universal transmitter (5817)	6b.	Check programming switches on
			programmed wrong.		transmitter.
7.	Intrusion alarm for	7a.	Protected door or window opened while	7a.	Check with all occupants of protected
	no apparent reason.		system armed.		home.
		7b.	Improper user operation of exit/entry
			delays.	7b.	Check setting of entry and exit delays.
		7c.	Magnets located too far from switches,	7c.	Check all openings for proper switch
			and/or doors and windows not properly		and magnet orientation.
			aligned.

–56–