Honeywell LYNXR Series, LYNXR-EN setup guide System Communication, Communication Overview

System Communication

This section provides an explanation of formats this system accommodates for reporting alarms and other system conditions to the central station. The process of a successful transmission consists of both the method of communication between the control panel and the central station receiver, and the actual way the information is sent and displayed at the central station.

Communication Overview

When the panel calls the central station receiver, it waits to hear a “handshake” frequency from the receiver to confirm that the receiver is on-line and ready to receive its message. Once the panel hears the handshake it is programmed to listen for, it sends its message. The panel then waits for a “kissoff” frequency from the receiver acknowledging that the message was received and understood.

3

If the handshake frequency is not given or is not understood by the panel, the panel will not send its message. Once the handshake frequency is received and understood by the panel, the panel will send its message. If there is an error in the transmission (the receiver does not receive a “valid” message), the kissoff frequency will not be given by the central station receiver.

The panel will make eight attempts to the primary telephone number and eight attempts to the secondary telephone number (if programmed) to get a valid message through. If the panel is not successful after its numerous attempts, the keypad will display “FC.” If the secondary number is a pager, “FC” displays after the first 8 attempts to the primary number.

The following chart defines the three sets of (handshake/kissoff) frequencies that the panel supports, and the different formats that can be sent for each.

FORMAT	HANDSHAKE	TRANSMITS DATA	KISSOFF	TRANSMIT TIME
Low Speed	1400Hz	1900Hz (10PPS)	1400Hz	Under 15 seconds
3+1		(Standard report)
4+1
4+2
Sescoa/Rad	2300Hz	1900Hz (20PPS)	2300Hz	Under 10 seconds
3+1		(Standard report)
4+1
4+2
Express	1400–2300Hz	DTMF (10 cps)	1400Hz	Under 3 seconds
4+2
Contact ID®	1400–2300Hz	DTMF (10 cps)	1400Hz	Under 3 seconds

Report Code Formats

3+1 and 4+1 Standard Formats	Comprise a 3- (or 4-) digit subscriber number and a single digit report
	code (e.g. alarm, trouble, restore, open, close, etc).
3+1 and 4+1 Expanded Formats	Comprise a 3- (or 4-) digit subscriber number, and a 2-digit report
	code. The first digit is displayed on the first line, followed by a second
	line where the first digit is repeated 3 (or 4) times and followed by the
	second digit. This is the “expanded” digit.
4+2 Format	Comprises a 4-digit subscriber number and 2-digit report code.
ADEMCO Contact ID®	Comprises a 4-digit subscriber number, 1-digit event qualifier
Reporting Format	(“new” or “restore”), 3-digit event code, and 3-digit zone number, user
	number, or system status number (see the following page).

The following table shows the message formats for 3+1, 4+1 and 4+2 reports, where:

SSS or SSSS	=	Subscriber ID		C	= Close Code (1st Digit)
A	=	Alarm Code (1st digit)	U	=	User Number (in hex)
Z	=	Typically Zone Number* (2nd digit)	Gg	=	Test Code (1st & 2nd digits)
Tt	=	Trouble Code (1st & 2nd digits)	R	=	Alarm Restore Code
Bb	=	Bypass Code (1st & 2nd digits)	R T t	=	Trouble Restore Code (1st & 2nd digits)
EA C	=	AC Loss Code (1st & 2nd digits)	R B b	=	Bypass Restore Code (1st & 2nd digits)
LL B	=	Low Battery Code (1st & 2nd digits)	R A A C	=	AC Restore Code (1st & 2nd digits)
O	=	Open Code (1st Digit)	R L L B	=	Battery Restore Code (1st & 2nd digits)

*Zone numbers for: [*] & [#], or [B] = 99; [1] + [*], or [A] = 95; [3] + [#], or [C] = 96; Duress = 92

–54–