Honeywell LYNXR Series, LYNXR-EN Enhanced Zone Programming Mode, Serial number, Voice descriptor

✻56 Enhanced Zone Programming Mode

			Manual entry
			Enter "1" to advance to Serial number prompt (1b).
			Copy the previous serial number
			Enter “2” to copy the previous serial number entered.
			Return to Prompt (E)
			Enter “#” to return to Loop Number prompt (E).
			Enter transmitter later
			Enter “0” or “✻” if you wish to enter the transmitter later, using the ✻83
			Enhanced Sequential Mode described later in this manual.
			Notes: (1) The panel will listen only when it is in the idle loop waiting for
			key entry and a serial number has been entered. If a key is
			entered, the function must be completed and the panel will
			listen again.
			(2) A long beep indicates illegal entry or duplicate serial
			number/loop entry
		Serial number	In this mode, the transmitter serial numbers can only be entered
Ib		Enter the transmitter’s 7-digit serial number.	manually.
		[#] = return to prompt 1A and reject any serial	Enter the 7-digit serial number printed on the transmitter. If an incorrect
		numbers entries that have been made.
			digit is entered, press the [#] key to backup to prompt (1A) and start over.
		[✻] = return to prompt 1A, (if a valid serial
			When all 7 digits are entered, press the [✻] key.
		number has been entered, the "L" is
		displayed and the serial number will be	If 52 seconds passes and no entry has been made, the system returns to
		copied into EEROM from the last serial	prompt (1A).
		entered into the buffer.)	Notes: (1) If the serial and loop number combination is already present
		Note: This prompt can be used only to manually
			the keypad will emit a single long beep and the system will
		enroll a serial number. RF enrollment will be	return to the (1A) prompt and “L” will be displayed.
		rejected and the current zone descriptor will	(2) If less than 7 digits have been entered, the keypad will emit a
		be announced, followed by a single long	single long beep and return to the (1A) prompt without
		beep and the system will return to prompt	displaying the “L”.
		(1A).	(3) If more than 7 digits have been entered, the first 6 digits will
			be saved along with the last digit that was entered (entering
			123456789 yields the serial number 1234569).
		Voice descriptor	Each zone can have a voice descriptor of up to 3 words that will be
IC		0 = skip to next zone (A)	announced whenever the system announces status for that zone.
		1 = enter descriptor mode; existing descriptor
		for this zone will be announced
		Descriptor 1	† see ✻84 Assign Zone Voice Descriptors section for vocabulary index
Id
	vi	Enter [#] + 2-digit vocabulary index number†	Use the [6] or [8] key to advance as described.
		of first descriptor word for this zone.
			To change the entered index number before pressing [6] or [8], simply press
		6 = accept word and advance to descriptor 2
			[#] + desired 2-digit vocabulary index number.
		(descriptor 2 will be announced)
			If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to return
		8 = accept word and advance to next zone	to zone number prompt.
		(prompt A) – entire zone descriptor will be
		announced
		Press any other key to repeat the selected word.
		Descriptor 2	† see ✻84 Assign Zone Voice Descriptors section for vocabulary index
IE
	vi	Enter [#] + 2-digit vocabulary index number†
		of second descriptor word for this zone.	Use the [6] or [8] key to advance as described.
		6 = accept word and advance to descriptor 3	To change the entered index number before pressing [6] or [8], simply press
		(descriptor 3 will be announced)	[#] + desired 2-digit vocabulary index number.
		8 = accept word and advance to next zone	If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to return
			to zone number prompt.
		(prompt A) – entire zone descriptor will be
		announced
		Press any other key to repeat the selected word.
		Descriptor 3	† see ✻84 Assign Zone Voice Descriptors section for vocabulary index
IF	vi	Enter [#] + 2-digit vocabulary index number†	Use the [6] or [8] key to advance as described.
		of third descriptor word for this zone.
			To change the entered index number before pressing [6] or [8], simply press
		6 or 8 = accept word and advance to next
			[#] + desired 2-digit vocabulary index number.
		zone (prompt A) – entire zone
			If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to return
		descriptor will be announced	to zone number prompt.
		Press any other key to repeat the selected word.

–30–