Manuals / Husky / Computer Equipment / Switch

Husky HME-423E, HME-421E user manual Updating Firmware by TFTP, Restoring Configurations by TFTP

Models: HME-423E HME-421E

1 77

Download 77 pages 56.55 Kb

Page 21

4-5.6 Updating Firmware by TFTP

Configuration Using a Web Browser

After finishing necessary configurations, click on Apply to save the settings.

4-5.6 Updating Firmware by TFTP

This feature allows the administrator to update the switch firmware. Before updating, make sure the TFTP server is ready and the firmware image is on the TFTP server.

TFTP Server IP Address Use this feature to fill in your TFTP server IP.

Firmware File Name Use this feature to fill in the name of the firmware image.

After finishing necessary configurations, click on Apply to save the settings.

4-5.7 Restoring Configurations by TFTP

You can restore EEPROM value from the TFTP server. Before doing so, make sure the image file is already placed on TFTP server. The HME-421E/423E will download the flash image.

TFTP Server IP Address Use this feature to fill in your TFTP server IP.

Firmware File Name Use this feature to fill in the correct file name to be restored.

After finishing necessary configurations, click on Apply to save the settings.

4-5.8 Backing up Configurations by TFTP

With this feature, the administrator can save the current configurations from the HME-421E/423E to the TFTP server, and then go to the TFTP restoration configuration page to restore the settings.

TFTP Server IP Address Use this feature to fill in your TFTP server IP.

Firmware File Name Use this feature to fill in the file name.

4-5

Image 21

Husky HME-423E, HME-421E Updating Firmware by TFTP, Restoring Configurations by TFTP, Backing up Configurations by TFTP

Contents

Industrial 4 10/100TX + 2 100FX Extended Temperature Managed Ethernet Switch User’s ManualHME-421E/423E HME-421E/423E Industrial Extended Temperature Managed Switch Husky Series Industrial Ethernet Switch SolutionsUser’s Manual Copyright NoticeChapter 2 Hardware Installation Table of ContentsChapter 3 Configuration Using Console Interface Chapter 4 Configuration Using a Web BrowserAppendix B Troubleshooting Appendix A SpecificationsAppendix C Command Set Lists Chapter 5 Network ApplicationsQoS Commands Set Chapter 1-2 Product FeaturesIntroduction 1-1 Overview1-3 Package Checklist Hardware Installation 2-1 Dimensions and Panel LayoutChapter 2-3 RJ-45 Ports 2-2 LED IndicatorsLED Name LED ColorMDI-X 2-4 Fiber Ports2-5 Installing Your Ethernet Direct Switch 2-5.1 Mounting The Switch2-5.1.1 DIN-Rail Mounting 2-5.1.2 Wall Mounting 2-5.2 Wiring The Power Inputs2-5.4 Cabling 2-5.3 Wiring The Fault Alarm ContactHardware Installations 3-1 Connecting Console Port Configuration Using Console Interface3-2 Login The Console Interface 3-3 CLI ManagementAccess Method 3-4 Command LevelsAbout This Mode configure4-3 System Login Configuration Using a Web Browser4-1 About Web-based Management Interface 4-2 Preparing for Web-based Management4-4 Management Main Screen 4-5 Basic Settings4-5.1 System Information System Name4-5.2 Port Statistics 4-5.4 Fault Relay Alarm 4-5.7 Restoring Configurations by TFTP 4-5.8 Backing up Configurations by TFTP4-5.6 Updating Firmware by TFTP 4-5.9 Saving Configuration Files 4-6 Advanced Management Settings4-5.10 Factory Default 4-5.11 Rebooting SystemSpeed Destination Port 4-6.3 Port MirroringSource Port 4-6.4 DHCP ServerLow IP Address DHCP ServerHigh IP Address Subnet MaskSyslog Client Mode 4-6.7 System Event Log 4-6.7.1 Syslog ConfigurationSystem Log Server IP AddressAuthentication 4-6.7.2 SMTP ConfigurationPassword Confirm Password4-6.7.3 Event Configuration System event selectionPort event selection SNTP Client 4-6.8 SNTP ConfigurationDaylight Saving Time UTC TimezoneSNTP Sever URL 4-6.10 Port Trunking 4-6.10.1 Aggregator SettingsSystem Priority Group ID4-6.10.2 Aggregator Information LACP DisabledGroup Key Port MemberConfiguration Using a Web Browser LACP Enabled4-17 Active 4-6.10.3 State ActivityThe port automatically sends LACP protocol packets Passive4-6.11.1 Port-based VLAN 4-6.11 VLAN ConfigurationTo add a new VLAN group. The maximum number of VLAN groups is VLAN Operation Mode 802.1Q ConfigurationEnable GVRP 4-6.11.2 IEEE 802.1Q Tag-based VLANLink Type PortUntagged VID Tagged VIDConfiguration Using a Web Browser 4-6.11.2.2 Group Configuration4-23 Use an 8, 4, 2, 1 weighted fair queuing scheme 4-6.12 QoS ConfigurationQoS Policy Use the strict priority schemeA message sent from the querier IGMP router or switch asking for a 4-6.13 IGMP ConfigurationMessage DescriptionAgent Mode 4-6.14 SNMP ConfigurationLeave Group 4-6.14.1 Community Strings4-6.14.3 SNMP v3 Configuration 4-6.14.2 Trap ConfigurationIP Address CommunityContext Table Access Table 4-6.15 LLDP Configuration LLDP ProtocolLLDP Interval 4-6.16.1 System Configuration 4-6.16 Rapid Spanning Tree Protocol Configuration RSTPRSTP Mode Forward Delay TimeAdmin Edge Admin P2PAdmin Non Stp 4-6.17 X-Ring ConfigurationMark the check box to enable the Dual Ring function. The difference This feature allows the administrator o enable the Dual Ring functionworking port in a Dual Homing topology between Dual Ring and Couple Ring is that Dual Ring only needs a unit4-6.18.1 System Configuration 4-6.18 802.1X/Radius ConfigurationIEEE 802.1x Protocol Radius Server IPDisable 4-6.18.2 Port Configuration4-6.18.3 Misc Configuration RejectServer Timeout Supplicant Timeout4-6.19.1 Static MAC Address Settings Max RequestsMAC Address 4-6.19.2 MAC Filtering4-6.19.3 All MAC Addresses Port No4-6.19.4 Multicast Filtering IP AddressMember Ports 5-1 X-Ring Application Network Applications5-2 Couple Ring Chapter5-3 Dual Homing Network Applications 5-4 Dual Ring Appendix A SpecificationsPower Requirements InterfaceManagement Specifications GVRP groups up to Appendix B TroubleshootingC-1 Commands Set List Command Set ListsC-2 System Commands Set Appendix CPortid C-3 Port Commands Setswitchconfig#interface fastEthernet C-5 VLAN Commands Set C-4 Trunk Commands Setswitch#vlan database C-6 Spanning Tree Commands Set C-8 IGMP Commands Set C-7 QoS Commands SetC-10 SNMP Commands Set C-9 Mac / Filter Table Commands Setremove C-12 802.1x Commands Set C-11 Port Mirroring Commands SetC-13 TFTP Commands Set SystemLog, SMTP and Event Commands Set C-14Alert@test.com C-16 X-Ring Commands Set C-15 SNTP Commands SetDual Homing Port