Manuals / Husky / Computer Equipment / Switch

Husky HME-421E, HME-423E user manual Hardware Installations

Models: HME-423E HME-421E

1 77

Page 14

Hardware Installations

Before connecting any network device, make sure network devices support auto MDI/MDI-X. If not support, use the cross over Category 5 cables.

After all wiring and connection are done and the LED lights on the switch’s front panel show normal status, the hardware installation is complete.

2-7

Page 14

Image 14

Husky HME-421E, HME-423E user manual Hardware Installations

Contents

HME-421E/423E Industrial 4 10/100TX + 2 100FX Extended TemperatureManaged Ethernet Switch User’s Manual User’s Manual Husky Series Industrial Ethernet Switch SolutionsHME-421E/423E Industrial Extended Temperature Managed Switch Copyright NoticeChapter 3 Configuration Using Console Interface Table of ContentsChapter 2 Hardware Installation Chapter 4 Configuration Using a Web BrowserAppendix C Command Set Lists Appendix A SpecificationsAppendix B Troubleshooting Chapter 5 Network ApplicationsQoS Commands Set Introduction 1-2 Product FeaturesChapter 1-1 Overview1-3 Package Checklist Chapter Hardware Installation2-1 Dimensions and Panel Layout LED Name 2-2 LED Indicators2-3 RJ-45 Ports LED Color2-4 Fiber Ports MDI-X2-5.1.1 DIN-Rail Mounting 2-5 Installing Your Ethernet Direct Switch2-5.1 Mounting The Switch 2-5.2 Wiring The Power Inputs 2-5.1.2 Wall Mounting2-5.3 Wiring The Fault Alarm Contact 2-5.4 CablingHardware Installations 3-2 Login The Console Interface Configuration Using Console Interface3-1 Connecting Console Port 3-3 CLI ManagementAbout This Mode 3-4 Command LevelsAccess Method configure4-1 About Web-based Management Interface Configuration Using a Web Browser4-3 System Login 4-2 Preparing for Web-based Management4-5.1 System Information 4-5 Basic Settings4-4 Management Main Screen System Name4-5.2 Port Statistics 4-5.4 Fault Relay Alarm 4-5.6 Updating Firmware by TFTP 4-5.7 Restoring Configurations by TFTP4-5.8 Backing up Configurations by TFTP 4-5.10 Factory Default 4-6 Advanced Management Settings4-5.9 Saving Configuration Files 4-5.11 Rebooting SystemSpeed Source Port 4-6.3 Port MirroringDestination Port 4-6.4 DHCP ServerHigh IP Address DHCP ServerLow IP Address Subnet MaskSystem Log Server IP 4-6.7 System Event Log 4-6.7.1 Syslog ConfigurationSyslog Client Mode AddressPassword 4-6.7.2 SMTP ConfigurationAuthentication Confirm PasswordPort event selection 4-6.7.3 Event ConfigurationSystem event selection Daylight Saving Time 4-6.8 SNTP ConfigurationSNTP Client UTC TimezoneSNTP Sever URL System Priority 4-6.10.1 Aggregator Settings4-6.10 Port Trunking Group IDGroup Key LACP Disabled4-6.10.2 Aggregator Information Port Member4-17 Configuration Using a Web BrowserLACP Enabled The port automatically sends LACP protocol packets 4-6.10.3 State ActivityActive Passive4-6.11 VLAN Configuration 4-6.11.1 Port-based VLANTo add a new VLAN group. The maximum number of VLAN groups is Enable GVRP 802.1Q ConfigurationVLAN Operation Mode 4-6.11.2 IEEE 802.1Q Tag-based VLANUntagged VID PortLink Type Tagged VID4-23 Configuration Using a Web Browser4-6.11.2.2 Group Configuration QoS Policy 4-6.12 QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme Use the strict priority schemeMessage 4-6.13 IGMP ConfigurationA message sent from the querier IGMP router or switch asking for a DescriptionLeave Group 4-6.14 SNMP ConfigurationAgent Mode 4-6.14.1 Community StringsIP Address 4-6.14.2 Trap Configuration4-6.14.3 SNMP v3 Configuration CommunityContext Table Access Table LLDP Interval 4-6.15 LLDP ConfigurationLLDP Protocol RSTP Mode 4-6.16 Rapid Spanning Tree Protocol Configuration RSTP4-6.16.1 System Configuration Forward Delay TimeAdmin Non Stp Admin P2PAdmin Edge 4-6.17 X-Ring Configurationworking port in a Dual Homing topology This feature allows the administrator o enable the Dual Ring functionMark the check box to enable the Dual Ring function. The difference between Dual Ring and Couple Ring is that Dual Ring only needs a unitIEEE 802.1x Protocol 4-6.18 802.1X/Radius Configuration4-6.18.1 System Configuration Radius Server IP4-6.18.3 Misc Configuration 4-6.18.2 Port ConfigurationDisable Reject4-6.19.1 Static MAC Address Settings Supplicant TimeoutServer Timeout Max Requests4-6.19.3 All MAC Addresses 4-6.19.2 MAC FilteringMAC Address Port NoMember Ports 4-6.19.4 Multicast FilteringIP Address 5-2 Couple Ring Network Applications5-1 X-Ring Application Chapter5-3 Dual Homing Network Applications 5-4 Dual Ring Power Requirements SpecificationsAppendix A InterfaceManagement Specifications GVRP groups up to Troubleshooting Appendix BC-2 System Commands Set Command Set ListsC-1 Commands Set List Appendix CC-3 Port Commands Set Portidswitchconfig#interface fastEthernet C-4 Trunk Commands Set C-5 VLAN Commands Setswitch#vlan database C-6 Spanning Tree Commands Set C-7 QoS Commands Set C-8 IGMP Commands SetC-9 Mac / Filter Table Commands Set C-10 SNMP Commands Setremove C-11 Port Mirroring Commands Set C-12 802.1x Commands SetC-13 TFTP Commands Set Alert@test.com SystemLog, SMTP and Event Commands SetC-14 C-15 SNTP Commands Set C-16 X-Ring Commands SetDual Homing Port