Port Mirroring Commands Set | Husky HME-421E, HME-423E specification

				Command Set Lists

	View Name] [Notify View
	Name]
	no snmpv3 mibview view	G	Remove specified	switch(config)#no snmpv3 mibview
	[View Name]		mibview table of SNMPV3	view V1 type Excluded sub-oid 1.3.6.1
	type		agent.
	[ExcludedIncluded]
	sub-oid
	[OID]

C-11 Port Mirroring Commands Set

Commands	Level	Description	Example
monitor	I	Configure source port of	switch(config)#interface fastEthernet 2
[RXTXBoth]		monitor function	switch(config-if)#monitor RX
monitor rx [Port ID]	G	Set RX destination port of	switch(config)#monitor rx 2
		monitor function
monitor tx [Port ID]	G	Set TX destination port of	switch(config)#monitor tx 3
		monitor function
show monitor	P	Show port monitor	switch#show monitor
		information
show monitor	I	Show port monitor	switch(config)#interface fastEthernet 2
		information	switch(config-if)#show monitor
no monitor	I	Disable source port of	switch(config)#interface fastEthernet 2
		monitor function	switch(config-if)#no monitor

C-12 802.1x Commands Set

Commands	Level	Description	Example
8021x enable	G	Use the 802.1x global	switch(config)# 8021x enable
		configuration command to
		enable 802.1x protocols.
8021x system radiusip	G	Use the 802.1x system	switch(config)# 8021x system radiusip
[IP address]		radius IP global	192.168.1.1
		configuration command to
		change the radius server
		IP.
8021x system serverport	G	Use the 802.1x system	switch(config)# 8021x system
[port ID]		server port global	serverport 1812
		configuration command to
		change the radius server
		port.
8021x system accountport	G	Use the 802.1x system	switch(config)# 8021x system
[port ID]		account port global	accountport 1813
		configuration command to
		change the accounting
		port.
8021x system sharedkey	G	Use the 802.1x system	switch(config)# 8021x system
[ID]		share key global	sharedkey 123456
		configuration command to
		change the shared key
		value.
8021x system nasid	G	Use the 802.1x system	switch(config)# 8021x system nasid
[words]		nasid global configuration	test1

C-10

Image 72

Husky HME-421E, HME-423E user manual Port Mirroring Commands Set, 12 802.1x Commands Set

Contents

HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Hardware Installation Dimensions and Panel LayoutFront Panel Side Panel Back Panel Bottom Panel LED Indicators RJ-45 PortsLED Name LED Color LED Function 1 RJ-45 Pin Assignments Fiber Ports Pin Installing Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall Mounting Wiring The Fault Alarm Contact CablingPage Configuration Using Console Interface Connecting Console PortLogin The Console Interface CLI Management Command Levels Modes Access Method Prompt Exit Method About This ModeConfigure Database Configuration Using a Web Browser System LoginAbout Web-based Management Interface Preparing for Web-based Management Basic Settings Management Main Screen User Authentication Confirm passwordPort Statistics Port Fault Relay Alarm Power FailureIP Configuration Port Link Down/Broken Restoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Speed DuplexSecurity Rate Limiting Port Mirroring Destination PortSource Port Dhcp Server Low IP Address High IP AddressLease Time sec Port and IP Bindings by Dhcp Server System Event Log Syslog Configuration Syslog Client ModeSystem Log Server IP Address Smtp Configuration AuthenticationEmail Alert Smtp Server IP Event Configuration System event selectionPort event selection Sntp Configuration Sntp ClientDaylight Saving Time UTC Timezone Mins Switch Timer IP Security ModeEnable Http Server Enable Telnet Server Aggregator Settings Port TrunkingSystem Priority Group ID Lacp Disabled Aggregator InformationGroup Key Port Member Lacp Enabled State Activity Vlan Configuration Port-based VlanPage 11.2.1 802.1Q Configuration Vlan Operation Mode Enable GvrpIeee 802.1Q Tag-based Vlan Management Vlan ID Link Type Untagged VIDTagged VID Group Configuration QoS Configuration Use an 8, 4, 2, 1 weighted fair queuing schemeQoS Policy Use the strict priority scheme Igmp Configuration Snmp Configuration Agent ModeLeave Group Community Strings Trap Configuration Snmp v3 ConfigurationCommunity Trap Version Context Table Context Name Group Table Security Name User ID Access Table Context Prefix Security LevelContext Match Rule Read View Name Lldp Configuration Lldp ProtocolLldp Interval Rapid Spanning Tree Protocol Configuration Rstp System ConfigurationRstp Mode Forward Delay Time Admin P2P Admin EdgeAdmin Non Stp Ring Configuration Enable Ring Enable Couple RingEnable Dual Homing Enable Dual Ring 18 802.1X/Radius Configuration Ieee 802.1x ProtocolRadius Server IP Server Port Disable Misc ConfigurationReject Accept Supplicant Timeout Server TimeoutStatic MAC Address Settings Max Requests MAC Filtering All MAC Addresses Multicast Filtering Member Ports Network Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring Connection Network Applications Example of Dual Ring Connection Diagram Dual Ring Specifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix B Command Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands Set Switch#vlan database Switchvlan#vlanmode portbaseSwitchvlan#vlanmode 802.1q Ported based Vlan configuration Spanning Tree Commands Set QoS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set Switchconfig#snmpv3 context-name Switchconfig#snmpv3 user test01Group G1 password AuthPW PrivPW Switchconfig#snmpv3 mibview view Port Mirroring Commands Set 12 802.1x Commands Set Tftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands Set Switchconfig#ring homingport Switch#show ringSwitchconfig# no ring couplering Switchconfig# no ring dualhoming