Manuals / Husky / Computer Equipment / Switch

Husky HME-423E Appendix A, Specifications, Interface, Power Requirements, Physical, Environmental

Models: HME-423E HME-421E

1 77

Download 77 pages 56.55 Kb

Page 59

Appendix A

Appendix A

Specifications

HME-421E/423E Product Specifications are as follows:

Hardware

Interface

	Total Ports	6 ports

	RJ-45 ports	4 10/100Base-T(X) auto-negotiation speed, Full/Half duplex, auto
		MDI/MDI-X

	Fiber ports	2 10/100Base-FX SC type multi-mode (HME-421E)
		2 10/100Base-FX SC type single-mode (HME-423E)

	LEDs	Per Port	Link/Activity (Green), Full duplex/Collision
			(Orange)

		Per Unit	Power (Green), Power 1 (Green), Power 2
			(Green), Fault (Orange), R.M.(Green)

	Alarm Contact	1A@24VDC

	Power Requirements

	Power Input	12 to 48VDC redundant power with removable terminal block

	Power Consumption	8.4 watts max.

	Power Protection	Power Reverse Polarity

	Physical

	Dimensions	IP-30 standard, 54mm (W) x 105mm (D) x 135mm (H)

	Installation	DIN Rail mounting/Wall mounting

	Environmental

	Operating Temperature	Extended: -40 to 80℃

	Storage Temperature	-40 to 85 ℃

	Operating Humidity	5% to 95% RH (Non-condensing)

	Technology
		IEEE 802.3 10Base-T Ethernet
		IEEE 802.3u 100Base-TX/100Base-FX
		IEEE 802.3x Flow Control
		IEEE 802.3ad Port trunk with LACP
	Standard	IEEE802.1D Spanning Tree Protocol
	Standard	IEEE802.1w Rapid STP
		IEEE802.1w Rapid STP
		IEEE802.1p Class of Service
		IEEE802.1Q VLAN Tagging
		IEEE 802.1X User Authentication (Radius)
		IEEE 802.1AB LLDP

	Protocol Technology	CSMA/CD

	Switching Architecture	Store and Forward

	Regulatory Approvals
	EMI	FCC Class A

			A-1

Image 59

Husky HME-423E, HME-421E user manual Appendix A, Specifications, Interface, Power Requirements, Physical, Environmental

Contents

Industrial 4 10/100TX + 2 100FX Extended Temperature Managed Ethernet Switch User’s ManualHME-421E/423E Copyright Notice Husky Series Industrial Ethernet Switch SolutionsHME-421E/423E Industrial Extended Temperature Managed Switch User’s ManualChapter 4 Configuration Using a Web Browser Table of ContentsChapter 2 Hardware Installation Chapter 3 Configuration Using Console InterfaceChapter 5 Network Applications Appendix A SpecificationsAppendix B Troubleshooting Appendix C Command Set ListsQoS Commands Set 1-1 Overview 1-2 Product FeaturesChapter Introduction1-3 Package Checklist Chapter Hardware Installation2-1 Dimensions and Panel Layout LED Color 2-2 LED Indicators2-3 RJ-45 Ports LED NameMDI-X 2-4 Fiber Ports2-5.1.1 DIN-Rail Mounting 2-5 Installing Your Ethernet Direct Switch2-5.1 Mounting The Switch 2-5.1.2 Wall Mounting 2-5.2 Wiring The Power Inputs2-5.4 Cabling 2-5.3 Wiring The Fault Alarm ContactHardware Installations 3-3 CLI Management Configuration Using Console Interface3-1 Connecting Console Port 3-2 Login The Console InterfaceModes 3-4 Command LevelsAccess Method configure4-2 Preparing for Web-based Management Configuration Using a Web Browser4-3 System Login 4-1 About Web-based Management InterfaceSystem Name 4-5 Basic Settings4-4 Management Main Screen 4-5.1 System Information4-5.2 Port Statistics 4-5.4 Fault Relay Alarm 4-5.6 Updating Firmware by TFTP 4-5.7 Restoring Configurations by TFTP4-5.8 Backing up Configurations by TFTP 4-5.11 Rebooting System 4-6 Advanced Management Settings4-5.9 Saving Configuration Files 4-5.10 Factory DefaultSpeed 4-6.4 DHCP Server 4-6.3 Port MirroringDestination Port Source PortSubnet Mask DHCP ServerLow IP Address High IP AddressAddress 4-6.7 System Event Log 4-6.7.1 Syslog ConfigurationSyslog Client Mode System Log Server IPConfirm Password 4-6.7.2 SMTP ConfigurationAuthentication PasswordPort event selection 4-6.7.3 Event ConfigurationSystem event selection UTC Timezone 4-6.8 SNTP ConfigurationSNTP Client Daylight Saving TimeSNTP Sever URL Group ID 4-6.10.1 Aggregator Settings4-6.10 Port Trunking System PriorityPort Member LACP Disabled4-6.10.2 Aggregator Information Group Key4-17 Configuration Using a Web BrowserLACP Enabled Passive 4-6.10.3 State ActivityActive The port automatically sends LACP protocol packets4-6.11.1 Port-based VLAN 4-6.11 VLAN ConfigurationTo add a new VLAN group. The maximum number of VLAN groups is 4-6.11.2.1 802.1Q ConfigurationEnable GVRP 4-6.11.2 IEEE 802.1Q Tag-based VLANTagged VID PortLink Type Untagged VID4-23 Configuration Using a Web Browser4-6.11.2.2 Group Configuration Use the strict priority scheme 4-6.12 QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme QoS PolicyDescription 4-6.13 IGMP ConfigurationA message sent from the querier IGMP router or switch asking for a MessageStrings 4-6.14 SNMP ConfigurationLeave Group 4-6.14.1 Community StringsCommunity 4-6.14.2 Trap Configuration4-6.14.3 SNMP v3 Configuration IP AddressContext Table Access Table LLDP Interval 4-6.15 LLDP ConfigurationLLDP Protocol RSTP Mode 4-6.16 Rapid Spanning Tree Protocol Configuration RSTP4-6.16.1 System Configuration 4-6.16.2 Port Configuration4-6.17 X-Ring Configuration Admin P2PAdmin Edge Admin Non Stpbetween Dual Ring and Couple Ring is that Dual Ring only needs a unit This feature allows the administrator o enable the Dual Ring functionMark the check box to enable the Dual Ring function. The difference working port in a Dual Homing topologyRadius Server IP 4-6.18 802.1X/Radius Configuration4-6.18.1 System Configuration IEEE 802.1x ProtocolReject 4-6.18.2 Port ConfigurationDisable 4-6.18.3 Misc ConfigurationMax Requests Supplicant TimeoutServer Timeout 4-6.19.1 Static MAC Address SettingsPort No 4-6.19.2 MAC FilteringMAC Address 4-6.19.3 All MAC AddressesMember Ports 4-6.19.4 Multicast FilteringIP Address Chapter Network Applications5-1 X-Ring Application 5-2 Couple Ring5-3 Dual Homing Network Applications 5-4 Dual Ring Interface SpecificationsAppendix A Power RequirementsManagement Specifications GVRP groups up to Appendix B TroubleshootingAppendix C Command Set ListsC-1 Commands Set List C-2 System Commands SetPortid C-3 Port Commands Setswitchconfig#interface fastEthernet C-5 VLAN Commands Set C-4 Trunk Commands Setswitch#vlan database C-6 Spanning Tree Commands Set C-8 IGMP Commands Set C-7 QoS Commands SetC-10 SNMP Commands Set C-9 Mac / Filter Table Commands Setremove C-12 802.1x Commands Set C-11 Port Mirroring Commands SetC-13 TFTP Commands Set Alert@test.com SystemLog, SMTP and Event Commands SetC-14 C-16 X-Ring Commands Set C-15 SNTP Commands SetDual Homing Port