Trunk Commands Set, Vlan Commands Set | Husky HME-421E, HME-423E

				Command Set Lists

	show interface configuration	I	Show interface	switch(config)#interface fastEthernet 2
			configuration status	switch(config-if)#show interface
				configuration
	show interface status	I	Show interface actual	switch(config)#interface fastEthernet 2
			status	switch(config-if)#show interface status
	show interface accounting	I	Show interface statistic	switch(config)#interface fastEthernet 2
			counter	switch(config-if)#show interface
				accounting
	no accounting	I	Clear interface	switch(config)#interface fastEthernet 2
			accounting information	switch(config-if)#no accounting

C-4 Trunk Commands Set

Commands	Level	Description	Example
aggregator priority	G	Set port group system	switch(config)#aggregator priority 22
[1~65535]		priority
aggregator activityport	G	Set activity port	switch(config)#aggregator activityport
[Group ID]			2
[Port Numbers]
aggregator group	G	Assign a trunk group with	switch(config)#aggregator group 1 1-4
[GroupID] [Port-list]		LACP active.	lacp workp 2 or
lacp		[GroupID]: 1~3	switch(config)#aggregator group 2
workp		[Port-list]: Member port	1,4,3 lacp workp 3
[Workport]		list. This parameter could
		be a port range (ex.1-4) or
		a port list separate by a
		comma (ex.2, 3, 6)
		[Workport]: The amount of
		work ports. This value
		could not be less than
		zero or be large than the
		amount of member ports.
aggregator group	G	Assign a static trunk	switch(config)#aggregator group 1 2-4
[GroupID] [Port-list]		group.	nolacp or
nolacp		[GroupID]:1~3	switch(config)#aggregator group 1
		[Port-list]: Member port	3,1,2 nolacp
		list. This parameter could
		be a port range (ex.1-4) or
		a port list separate by a
		comma ex.2, 3, 6)
show aggregator	P	Show the information of	switch#show aggregator 1 or
		trunk group	switch#show aggregator 2 or
			switch#show aggregator 3

no aggregator lacp	G	Disable the LACP	switch(config)#no aggreator lacp 1
[GroupID]		function of trunk group

no aggregator group	G	Remove a trunk group	switch(config)#no aggreator group 2
[GroupID]

C-5 VLAN Commands Set

Commands

Level

Description

Example

C-4

Image 66

Husky HME-421E, HME-423E user manual Trunk Commands Set, Vlan Commands Set

Contents

HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Front Panel Side Panel Hardware InstallationDimensions and Panel Layout Back Panel Bottom Panel LED Name LED Color LED Function LED IndicatorsRJ-45 Ports 1 RJ-45 Pin Assignments Fiber Ports Pin Installing Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall Mounting Wiring The Fault Alarm Contact CablingPage Login The Console Interface Configuration Using Console InterfaceConnecting Console Port CLI Management Configure Command LevelsModes Access Method Prompt Exit Method About This Mode Database About Web-based Management Interface Configuration Using a Web BrowserSystem Login Preparing for Web-based Management Basic Settings Management Main Screen Port Statistics User AuthenticationConfirm password Port IP Configuration Fault Relay AlarmPower Failure Port Link Down/Broken Restoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Security SpeedDuplex Rate Limiting Source Port Port MirroringDestination Port Dhcp Server Lease Time sec Low IP AddressHigh IP Address Port and IP Bindings by Dhcp Server System Log Server IP System Event Log Syslog ConfigurationSyslog Client Mode Address Email Alert Smtp ConfigurationAuthentication Smtp Server IP Event Configuration System event selectionPort event selection Daylight Saving Time Sntp ConfigurationSntp Client UTC Timezone Enable Http Server Mins Switch TimerIP Security Mode Enable Telnet Server System Priority Aggregator SettingsPort Trunking Group ID Group Key Lacp DisabledAggregator Information Port Member Lacp Enabled State Activity Vlan Configuration Port-based VlanPage Ieee 802.1Q Tag-based Vlan 11.2.1 802.1Q Configuration Vlan Operation ModeEnable Gvrp Management Vlan ID Link Type Untagged VIDTagged VID Group Configuration QoS Policy QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme Use the strict priority scheme Igmp Configuration Leave Group Snmp ConfigurationAgent Mode Community Strings Community Trap ConfigurationSnmp v3 Configuration Trap Version Context Table Context Name Group Table Security Name User ID Context Match Rule Access Table Context PrefixSecurity Level Read View Name Lldp Configuration Lldp ProtocolLldp Interval Rstp Mode Rapid Spanning Tree Protocol Configuration RstpSystem Configuration Forward Delay Time Admin Non Stp Admin P2PAdmin Edge Ring Configuration Enable Dual Homing Enable RingEnable Couple Ring Enable Dual Ring Radius Server IP 18 802.1X/Radius ConfigurationIeee 802.1x Protocol Server Port Reject DisableMisc Configuration Accept Static MAC Address Settings Supplicant TimeoutServer Timeout Max Requests MAC Filtering All MAC Addresses Multicast Filtering Member Ports Network Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring Connection Network Applications Example of Dual Ring Connection Diagram Dual Ring Specifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix B Command Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands Set Switchvlan#vlanmode 802.1q Switch#vlan databaseSwitchvlan#vlanmode portbase Ported based Vlan configuration Spanning Tree Commands Set QoS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set Group G1 password AuthPW PrivPW Switchconfig#snmpv3 context-nameSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 mibview view Port Mirroring Commands Set 12 802.1x Commands Set Tftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands Set Switchconfig# no ring couplering Switchconfig#ring homingportSwitch#show ring Switchconfig# no ring dualhoming