Leave Group, Snmp Configuration, Community Strings | Husky HME-421E

Configuration Using a Web Browser

Leave Group

A message sent by a host to the querier to indicate that the host has quit to be a member of a specific multicast group.

This feature allows the administrator to enable IGMP protocol and IGMP Query function. The administrator will see the IGMP snooping information in this section -- different multicast group VIDs and member ports, and IP multicast addresses range from 224.0.0.0 through 239.255.255.255.

After finishing necessary configurations, click on Apply to save the settings.

4-6.14 SNMP Configuration

Simple Network Management Protocol (SNMP) is used to monitor exchange of information among devices in a network system. HME-421E/423E supports SNMP v1/v2c/v3.

4-6.14.1 Community Strings

This function is to use community strings for authentication.

	Strings	This feature allows the administrator to enter a name for the string.
	RO	RO means Read Only. This feature allows the requests accompanied by
	RO	this string to display MIB-object information.
		this string to display MIB-object information.
	RW	RW means Read & Write. This feature allows the requests accompanied
	RW	by this string to display MIB-object information and to set MIB object.

		This feature allows the administrator to select the SNMP version for
	Agent Mode	necessary configuration. Click on the version option required, and then
		click on Change to validate the settings.

After finishing necessary configurations, click on Apply to save the settings.

4-26

Image 42

Husky HME-421E, HME-423E user manual Leave Group, Snmp Configuration, Community Strings, Agent Mode

Contents

HME-421E/423E Copyright Notice Table of Contents Ring Application Couple Ring Dual Homing Dual Ring Page Product Features IntroductionOverview Package Checklist Front Panel Side Panel Hardware InstallationDimensions and Panel Layout Back Panel Bottom Panel LED Name LED Color LED Function LED IndicatorsRJ-45 Ports 1 RJ-45 Pin Assignments Fiber Ports Pin Installing Your Ethernet Direct Switch Mounting The SwitchDIN-Rail Mounting Wiring The Power Inputs Wall Mounting Wiring The Fault Alarm Contact CablingPage Login The Console Interface Configuration Using Console InterfaceConnecting Console Port CLI Management Configure Command LevelsModes Access Method Prompt Exit Method About This Mode Database About Web-based Management Interface Configuration Using a Web BrowserSystem Login Preparing for Web-based Management Basic Settings Management Main Screen Port Statistics User AuthenticationConfirm password Port IP Configuration Fault Relay AlarmPower Failure Port Link Down/Broken Restoring Configurations by Tftp Backing up Configurations by TftpUpdating Firmware by Tftp Advanced Management Settings Security SpeedDuplex Rate Limiting Source Port Port MirroringDestination Port Dhcp Server Lease Time sec Low IP AddressHigh IP Address Port and IP Bindings by Dhcp Server System Log Server IP System Event Log Syslog ConfigurationSyslog Client Mode Address Email Alert Smtp ConfigurationAuthentication Smtp Server IP Event Configuration System event selectionPort event selection Daylight Saving Time Sntp ConfigurationSntp Client UTC Timezone Enable Http Server Mins Switch TimerIP Security Mode Enable Telnet Server System Priority Aggregator SettingsPort Trunking Group ID Group Key Lacp DisabledAggregator Information Port Member Lacp Enabled State Activity Vlan Configuration Port-based VlanPage Ieee 802.1Q Tag-based Vlan 11.2.1 802.1Q Configuration Vlan Operation ModeEnable Gvrp Management Vlan ID Link Type Untagged VIDTagged VID Group Configuration QoS Policy QoS ConfigurationUse an 8, 4, 2, 1 weighted fair queuing scheme Use the strict priority scheme Igmp Configuration Leave Group Snmp ConfigurationAgent Mode Community Strings Community Trap ConfigurationSnmp v3 Configuration Trap Version Context Table Context Name Group Table Security Name User ID Context Match Rule Access Table Context PrefixSecurity Level Read View Name Lldp Configuration Lldp ProtocolLldp Interval Rstp Mode Rapid Spanning Tree Protocol Configuration RstpSystem Configuration Forward Delay Time Admin Non Stp Admin P2PAdmin Edge Ring Configuration Enable Dual Homing Enable RingEnable Couple Ring Enable Dual Ring Radius Server IP 18 802.1X/Radius ConfigurationIeee 802.1x Protocol Server Port Reject DisableMisc Configuration Accept Static MAC Address Settings Supplicant TimeoutServer Timeout Max Requests MAC Filtering All MAC Addresses Multicast Filtering Member Ports Network Applications Ring ApplicationCouple Ring Dual Homing Example of Couple Ring Connection Network Applications Example of Dual Ring Connection Diagram Dual Ring Specifications TechnologyRegulatory Approvals Management Specifications Dhcp Troubleshooting Appendix B Command Set Lists Commands Set ListSystem Commands Set Port Commands Set Broadcast-multicast-flooded-unicast Broadcast-multicastBroadcast-only Trunk Commands Set Vlan Commands Set Switchvlan#vlanmode 802.1q Switch#vlan databaseSwitchvlan#vlanmode portbase Ported based Vlan configuration Spanning Tree Commands Set QoS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set Group G1 password AuthPW PrivPW Switchconfig#snmpv3 context-nameSwitchconfig#snmpv3 user test01 Switchconfig#snmpv3 mibview view Port Mirroring Commands Set 12 802.1x Commands Set Tftp Commands Set SystemLog, Smtp and Event Commands Set Sntp Commands Set Ring Commands Set Switchconfig# no ring couplering Switchconfig#ring homingportSwitch#show ring Switchconfig# no ring dualhoming