Integra DTR-7.4 Connecting -compatible AV Components, Connections for Remote Control

Connecting -compatible AV Components

The terminal on the DTR-7.4 is for connecting other Integra/Onkyo components equipped with the same terminal. When a component is connected to the terminal, it can be operated by the remote controller supplied with the DTR-7.4. In addition, when you

connect a component to the terminal, you can also perform the system operations given below.

Power on/ready function

When the DTR-7.4 is in the standby state, if an - connected component is turned on, the DTR-7.4 also turns on and the input source selected at the DTR-7.4 automatically switches to that component.

Beawarethatthisfunctionwillnotworkifthepowercordforthe -connected component is connected to theAC OUTLET on

the DTR-7.4, or if the DTR-7.4 has already been turned on.

Direct change function

When the play button is pressed on an -connected component, the input source selected at the DTR-7.4 automatically changes to that component.

Power off function

When the DTR-7.4 is placed in the standby state, all

-connected components are also automatically put into the standby state.

Also, if you press the On button on the DTR-7.4 remote controller while the DTR-7.4 is turned on, all - connected components (DVD players, CD players, MD recorders, tuners, etc.) are also turned on.

Connections for Remote Control ()

To connect components using the terminal, simply connect a remote control cable from this terminal to the terminal of the other component. An remote control cable with a 1/8 inch (3.5 mm) miniature two-conductor plug comes with every cassette tape deck, compact disc player,

MD recorder, and DVD player that has an terminal.

Integra/Onkyo DVD player

REMOTE

CONTROL

DIGITAL OUT

COAX

L

R

ANALOG

Remote

OUTPUT

control

cable

DIGITAL

AUDIO

IN

R

L

REMOTE

COAX

CONTROL

1

IN

DIGITAL

PRE OUT

ANTENNA

AUDIO

VIDEO

S VIDEO

COMPONENT

FRONT SPEAKERS

SURR SPEAKERS

IN

R

L

VIDEO

COAX

FRONT

MONITOR

OUTPUT

R

L

R

L

1

OUT

Y

R

L

2

SUB

CENTER

AM

OUT

ZONE 2

P

SURR

3

IN

DVD

P

SURR

R

L

OPT

BACK/

INPUT 1

ZONE 2

FM

1

75

OUT

Y

ETHERNET

VIDEO 1

(Net -Tune)

2

FRONT

MULTI CH

IN

P

CENTER

R

INPUT

AUDIO

SPEAKER

L

R

L

SUB

CENTER

3

PHONO

OUT

P

IN

VIDEO 2

R

L

SURR

INPUT 2

DIGITAL

CD

IN

Y

I R A

A

IN

ZONE 2

OUT

R

L

12V

OPT

OUT

IN

TRIGGER OUT

1

IN

VIDEO 3

P

RS232

SURR

BACK

TAPE

2

IN

VIDEO 4

P

GND

IN

OUT

B

REMOTE

R

L

R

L

VIDEO

S VIDEO

CONTROL

AUDIO

AUDIO

•When performing operations with -connected

components using the system, do not use the remote zone (Zone 2).

•For remote control operation, the audio connection cables must also be connected.

•If a component has two terminals, you can use either one to connect to the DTR-7.4. The other one can be used to daisy chain with another component.

•With Integra/Onkyo DVD players, you can enter the pre-program code so that you can operate the DVD player directly with the remote controller without

connecting the terminals (See page 89).

DTR-7.4

connector

Ex: Integra/Onkyo CD player

connector

Ex: Onkyo cassette tape deck

Remote control cable

26