Selecting the Appropriate Setting for Your Connections—Continued

Changing the Remote Controller’s Control ID

This section explains how to change the remote control- ler’s ID. You may need to change this if the DTR-7.4’s remote controller interferes with other Integra/Onkyo components located in the same room.

Note:

If you change the remote controller’s ID, be sure to select the same ID on the DTR-7.4. For details on setting up the DTR-7.4’s remote control ID, refer to the previous “Remote Setup Sub-menu” section. The default ID for both the DTR-7.4 and remote controller is 1.

1

Hold down the remote controller’s

 

Custom

Custom button for more than three

 

seconds.

 

The remote controller enters Custom

2

mode.

Roll the scroll wheel to select

 

 

“SETUP” menu, and then press

 

the scroll wheel.

3

 

 

 

Roll the scroll wheel to select ID

 

 

 

 

 

 

 

 

menu, and then press the scroll

 

 

 

 

 

 

 

 

wheel.

 

 

 

Speaker Setup

After you have installed the DTR-7.4, connected all the components, and determined the speaker layout, it is now time to perform the settings in the Speaker Setup Menu to optimize the sound acoustics for your environment and speaker layout.

Before you perform the following settings, it is important that you first determine the following items:

The types and sizes of the speakers that are connected.

The distance from each speaker to the normal listening position.

 

 

 

Monitor

 

 

Front

 

SW Center

 

Front

Left

 

 

Right

 

 

 

 

 

[

]

[

]m/ft

 

 

 

m/ft

 

 

 

 

 

 

[

]m/ft

 

[

]m/ft

SL

 

 

 

 

SR

[

 

]m/ft

 

[

]m/ft

[

]m/ft

 

[

]m/ft

 

 

SBL

 

SBR

 

4

Roll the scroll wheel to select an

 

 

ID—1 (default), 2, or 3—and then

 

press the scroll wheel.

 

Select the same ID as that set on the

 

DTR-7.4.

Basic Menu

0.Hardware Setup 1.Speaker Setup 2.Input Setup 3.Audio Adjust

Advanced Menu

[ENTER]Quit:[SETUP]

1.Speaker Setup

1.Speaker Config 2.Speaker Distance 3.Level Calibration

[ENTER]Quit:[SETUP]

TV Format Sub-menu

a. TV Format (Australian model only)

When you want to reconfigure the settings conforming to the television format used for the area where you use the DTR-7.4, use this sub-menu so that no time is wasted on detection.

Auto: This is the default setting. When you leave this setting unchanged, the television format is detected and automatically set by the DTR-7.4. PAL: Use this setting when you know that the televi- sion format is PAL.

NTSC: Use this setting when you know that the tele- vision format is NTSC.

0-4.TV Format

a.TV Format

:Auto

Quit:[SETUP]

If you want to perform these operations using the remote controller, first press the scroll wheel.

1 Display the main menu.

Press the Setup button on the front panel, or press the scroll wheel and then press the Setup button on the remote controller to display the main menu on the monitor and front display.

2

Use the

and

cursor buttons to select

 

“1. Speaker Setup” and then press the

 

Enter button.

 

 

The “Speaker Setup” menu appears.

 

 

 

 

3

Use the

and

cursor buttons to select

 

an item and then press the Enter button.

 

 

 

 

4

Use the

and

cursor buttons to select

 

an item and then use the and cursor

 

buttons to set the desired value.

 

 

5

Press the Setup button to exit the Setup

 

menu.

 

 

Press the Return button to return to the previous menu.

32

Page 32
Image 32
Integra DTR-7.4 instruction manual Speaker Setup, Changing the Remote Controller’s Control ID, TV Format Sub-menu