Integra DTR-7.4 Digital device DVD recorder, Satellite tuner, television, or settop box

Connecting to Audio/Video Equipment—Continued

Connecting a DVD Recorder or Other Digital Video Recording Device (VIDEO 2)

DIGITAL

PRE OUT

ANTENNA

AUDIO

VIDEO

S VIDEO

COMPONENT

IN

R

L

VIDEO

COAX

FRONT

MONITOR

OUTPUT

1

OUT

Y

R

L

2

SUB

CENTER

AM

OUT

ZONE 2

PB

DIGITAL

SURR

COMPONENT

3

SURR

FM

IN

DVD

PR

IN

ZONE 2

R

L

VIDEO

OPT

BACK/

INPUT 1

COAX

1

75

OUT

Y

INPUT 2

FRONT

VIDEO 1

2

MULTI CH

IN

PB

3

R

INPUT

AUDIO

L

R

L

SUB

CENTER

3

PHONO

OUT

PR

IN

VIDEO 2

Y

SURR

INPUT 2

DIGITAL

CD

IN

Y

OUT

R

L

IN

DIGITAL

OPT

OUT

1

SURR

IN

VIDEO 3

PB

OUT

2

BACK

TAPE

IN

VIDEO 4

PR

PB

OPT

GND

IN

L

R

L

R

S VIDEO

AUDIO

AUDIO

VIDEO

1

AUDIO

VIDEO

S VIDEO

PR

R

L

OUT

R

L

VIDEO 2

IN

R	L			Y
AUDIO		VIDEO	S VIDEO
OUTPUT		OUTPUT	OUTPUT	PB
DIGITAL
IN
OPT				PR
R	L			COMPONENT
AUDIO		VIDEO S VIDEO		VIDEO
INPUT		INPUT INPUT		OUTPUT
DIGITAL
OUT
COAX
Digital device		DVD recorder

Using RCA video connection cables, connect the video output jack (composite) of the device to the VIDEO 2 VIDEO IN jack of the DTR-7.4 and connect the video input jack of the device to the VIDEO 2 VIDEO OUT jack of the DTR-7.4. Or if the device has S video input and output jacks, connect them to the VIDEO 2 S VIDEO IN and OUT jacks of the DTR-7.4 using S video connection cables. Or if the device has component video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the DTR-7.4.

On the initial settings of the DTR-7.4, the VIDEO 2 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at Setup Menu → Input Setup → Video Setup → Component Video (See page 38).

Using RCA audio connection cables, connect the audio out- put jacks of the device to the VIDEO 2 AUDIO IN jacks of the DTR-7.4 and connect the audio input jacks of the device to the VIDEO 2 AUDIO OUT jacks of the DTR-7.4. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAX jack or DIGITAL IN OPT jack of the DTR-7.4, depending on the type of connector on the device.

On the initial settings of the DTR-7.4, the VIDEO 2 input source is set for digital input at the COAX 3 jack. If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (See page 36).

If the device has a digital input, connect it to the DIGI- TAL OUT OPT jack of the DTR-7.4 for digital record- ing of the REC OUT signal from the DTR-7.4.

However, if the same device also has a digital output and it has already been connected to the DTR-7.4, you cannot connect the digital input of the device to the DIGITAL OUT jack of the DTR-7.4 simultaneously.

Note:

The output from the DIGITAL OUT jack of the DTR-7.4 is only the digital signal input to the DIGITAL IN jack.

Connecting a Satellite Tuner, Televi- sion, or Settop Box (VIDEO 3 or 4)

Satellite tuner, television, or settop box

DIGITAL OUT

OPT

AUDIO		VIDEO	S VIDEO	AUDIO		VIDEO	S VIDEO
R	OUT	OUT	OUT	R	OUT	OUT	OUT
	L				L

	DIGITAL		PRE OUT		ANTENNA		AUDIO	INVIDEO	S VIDEO	VIDEOCOMPONENT	3
	IN		R	L						VIDEO
	COAX	FRONT							MONITOR	OUTPUT
	1								OUT	Y
							R	L
	2	SUB		CENTER		AM
								OUT	ZONE 2	PB	4
	3	SURR						ININ	DVD	VIDEOPR
		SURR	R	L
	OPT	BACK/			R		L			INPUT 1
		ZONE 2				75
	1					FM		OUT	VIDEO	Y	S VIDEO
	2	FRONT		MULTI CH AUDIO				IN		PB
									1
		R		INPUT	AUDIO
DIGITAL				L	R	L
		SUB		CENTER
	3					PHONO		OUT		PR
IN		SURR				IN			VIDEO 2
										INPUT 2
OPT	DIGITAL					CD		IN		Y
			R	L		OUT
	OPT
	OUT					IN
	1							IN	VIDEO 3	PB
3		SURR
		BACK				TAPE
	2							IN	VIDEO 4	PR
		GND				IN	R	L
					R	L			S VIDEO
					AUDIO		AUDIO	VIDEO

Using an RCA video connection cable, connect the video output jack (composite) of the device to the VIDEO 3 (or 4) VIDEO IN jack of the DTR-7.4. Or if the device has an S video output jack, connect it to the VIDEO 3 (or 4) S VIDEO IN jack of the DTR-7.4 using an S video connection cable. Or if the device has compo- nent video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the DTR-7.4.

On the initial settings of the DTR-7.4, the VIDEO 3 and 4 input sources are set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at Setup Menu → Input Setup → Video Setup → Component Video (See page 38). Using an RCA audio connection cable, connect the audio output jack of the device to the VIDEO 3 (or 4) AUDIO IN jacks of the DTR-7.4. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

22