Console Command-line Summary, Console Commands | Intel 10/100

C H A P T E R 3

Intel Express 10/100 Fast Ethernet Switch

Console Command-line Summary

Console Commands

help-kbd

Lists the help and shortcut keys.

banner

Displays the Console Manager logo.

clear

Clears the screen.

login

Exits Console Manager and displays the login screen.

logout

Exits Console Manager and any active Telnet session.

set-prompt <new_prompt> Changes the console prompt.

set-passwd

Changes the console password.

System Commands

sys-stat

Displays system status.

get-stst-level

Displays the selftest level.

set-stst-level {noneshortlong} Changes the selftest level.

warm-reset

Performs a warm reset of the switch.

cold-reset

Performs a cold reset of the switch, which is the same as powering it off then on again.

get-last-err

Displays information about the last fatal error.

init-nvram

Resets nonvolatile RAM (NVRAM) to default values.

set-line-slip {96001920038400}

Transfers the serial connection to SLIP mode and sets the baud.

get-sw-file

Displays the SNMP agent software filename.

32

Image 35

Intel 10/100 manual Console Command-line Summary, Console Commands, System Commands

Contents

User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow control Overview Topology Intel Express 10/100 Fast Ethernet Switch Installation and Setup Rcv Using the SwitchPort status LEDs Xmt Link Management status LEDs Fiber optic requirements Cabling RequirementsUTP requirements NIC RJ-45 MDI Straight-through vs. crossover cables Determining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical Configurations Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager remotely Accessing the Console Manager Means you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagram Set the IP configuration. Type the command Configuring the Snmp agent for IPCommands used To configure the Snmp agent Recommended environments Configuring a port for full duplexTo configure a port for full duplex To create an Svlan Creating Virtual LANs VLANs To create a VBD Create the two SVLANs. Type the commands Monitoring traffic To check traffic on a port Detecting speed mismatches Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting congested segments Statistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that group System Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database Commands Spanning Tree Commands Switching Statistics Commands Port Configuration Commands Logout Console CommandsHelp-kbd Banner Sys-stat System CommandsSet-passwd Set-stst-level Warm-resetCold-reset Get-stst-level Set-sw-file Init-nvramSet-line-slip Get-sw-file Sw-dnld Set-rsw-fileGet-tftp-srvr Set-tftp-srvr IP configuration IP Commands Set-ip-conf Get-bootpSet-bootp Set-ip Get-gatew Get-slip-confSet-slip Set-slip-conf Stops the active ping process. You can also press cC Ping CommandsPing Ping-stop Del-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Add-arp-entry Set-comm Snmp CommandsSnmp community strings Get-comm Get-traps Snmp trap message commandsGet-auth Set-auth Removes a station from the trap table Switching Database CommandsAdd-trap Del-trap Get-lt-entry Database control commands FF-FF-FF-FF-FF-FF Get-lt-16 Add-lt-entry Find-lt-addrDel-lt-entry Del-lt-addr Set-lt-age Custom filteringGet-lt-age Add-cf-entry Get-lt-filter Displays the custom filter table stored in Nvram Vlan CommandsDel-cf-entry Get-nv-cftbl Get-vbc-matrix Get-con-matrix Set-sec-vlan Set-vbc-domainDel-vbc-domain Get-vbc-tbl Monitor Get-svlan-tblDisplays the table of defined SVLANs Set-mon-port Example Spanning Tree Commands Get-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-prt-pcost Set-br-fwdelSet-prt-prio Set-prt-enb Get-port-cfg Port Configuration CommandsUse these commands to configure and display port settings Displays the current port configuration Set-port-fctrl Statistics CommandsSet-port-dplex Set-speed-sel Get-colls-cnt Get-eth-cnt Get-br-cnt Get-rmon-cntGet-sdist-cnt Displays the Rmon statistics packet size histogram for port 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control Problems Intel Express 10/100 Fast Ethernet Switch System Default Configuration Spanning tree Not installed see Accessories on nextPorts Console Manager Status Indicators per port SpecificationsFeatures Accessories Maximum Cabling Distances General IndicatorsBoot and Configuration Connector Interfaces AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Electrical SpecificationsPower Cord Specifications Electromagnetic Emissions and Safety Agency Approval Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling Index Control commands Get-authcommandGet-bootpcommand Database, switching Get-trapscommand Get-port-cfgcommand, 22Get-slipcommand Get-stpcommand MIB Set-commcommand Xmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access