General Indicators, Boot and Configuration, Mounting | Intel 10/100

A p p e n d i x

A Intel Express 10/100 Fast Ethernet Switch

General Indicators

Displays Management activity, SNMP presence, power supply status, device failure detection.

Boot and Configuration

NVRAM configuration loaded on power up and fully downloadable. Firmware local or remote downloadable. BOOTP supported.

Connector Interfaces

UTP/STP RJ-45 (MDI-X pin configuration; MDI or MDI-X for port 1) RS232

SC fiber optic (on optional 100BASE-FX media adapter)

Maximum Cabling Distances

Switch to switch or switch to NIC: Category 5 UTP: 328 feet (100 meters)

62.5/125µ multimode fiber: 1.2 miles (2 kilometers) at full duplex 1351 feet (412 meters) at half duplex

Switch to repeater:

Category 5 UTP: 328 feet (100 meters)

62.5/125µ multimode fiber: 525 feet (160 meters)

Standards Supported

10BASE-T

100BASE-TX, 100BASE-FX Fast Ethernet (IEEE 802.3u) FDSE (Full Duplex Switched Ethernet)

Spanning Tree (IEEE 802.1d)

Internet Hosts (RFC1122/1123) SMI (RFC1155)

SNMP (RFC 1157) MIB (RFC1556) MIB II (RFC 1213) ENET MIB (RFC1398) Bridge MIB (RFC1493) RMON (RFC1757)

UDP/IP (RFC768/950/1071/791)

Mounting

Standard 19-inch rack, with mounting brackets 1-inch minimum clearance, sides and back

78

Image 81

Intel 10/100 manual General Indicators, Boot and Configuration, Connector Interfaces, Maximum Cabling Distances, Mounting

Contents

User Guide First edition Contents Chapter Troubleshooting Connect the network devices to the switch Check the LEDs for power and linksNext steps Optional Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow control Overview Topology Intel Express 10/100 Fast Ethernet Switch Installation and Setup Port status LEDs Using the SwitchXmt Rcv Link Management status LEDs Cabling Requirements UTP requirementsFiber optic requirements NIC RJ-45 MDI Straight-through vs. crossover cables Determining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical Configurations Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches Repeater count limitations General rule forOne repeater hop for Configuring Accessing the Console Manager remotely Accessing the Console Manager Using the Console Manager Entering commandsMeans you can type one of the following Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagram Commands used Configuring the Snmp agent for IPTo configure the Snmp agent Set the IP configuration. Type the command Configuring a port for full duplex To configure a port for full duplexRecommended environments To create an Svlan Creating Virtual LANs VLANs To create a VBD Create the two SVLANs. Type the commands Monitoring traffic To check traffic on a port Detecting bad or poor quality cable Detecting faulty adapters or hub portsDetecting congested segments Detecting speed mismatches Statistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that group Console Command-line Summary Console CommandsSystem Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database Commands Spanning Tree Commands Switching Statistics Commands Port Configuration Commands Help-kbd Console CommandsBanner Logout System Commands Set-passwdSys-stat Cold-reset Warm-resetGet-stst-level Set-stst-level Set-line-slip Init-nvramGet-sw-file Set-sw-file Get-tftp-srvr Set-rsw-fileSet-tftp-srvr Sw-dnld IP configuration IP Commands Set-bootp Get-bootpSet-ip Set-ip-conf Set-slip Get-slip-confSet-slip-conf Get-gatew Ping Ping CommandsPing-stop Stops the active ping process. You can also press cC Get-arp-tbl Address Resolution Protocol ARP CommandsAdd-arp-entry Del-arp-entry Snmp community strings Snmp CommandsGet-comm Set-comm Get-auth Snmp trap message commandsSet-auth Get-traps Add-trap Switching Database CommandsDel-trap Removes a station from the trap table Get-lt-entry Database control commands FF-FF-FF-FF-FF-FF Get-lt-16 Del-lt-entry Find-lt-addrDel-lt-addr Add-lt-entry Custom filtering Get-lt-ageSet-lt-age Add-cf-entry Get-lt-filter Del-cf-entry Vlan CommandsGet-nv-cftbl Displays the custom filter table stored in Nvram Get-vbc-matrix Get-con-matrix Del-vbc-domain Set-vbc-domainGet-vbc-tbl Set-sec-vlan Displays the table of defined SVLANs Get-svlan-tblSet-mon-port Monitor Example Spanning Tree Commands Get-stp Set-stpGet-st-bcfg Get-st-pcfg Get-st-syscfgDisplays the spanning tree state for all ports Set-br-prio Set-br-maxageSet-br-hellot Set-prt-prio Set-br-fwdelSet-prt-enb Set-prt-pcost Use these commands to configure and display port settings Port Configuration CommandsDisplays the current port configuration Get-port-cfg Set-port-dplex Statistics CommandsSet-speed-sel Set-port-fctrl Get-colls-cnt Get-eth-cnt Get-sdist-cnt Get-rmon-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control Problems Intel Express 10/100 Fast Ethernet Switch System Default Configuration Ports Not installed see Accessories on nextConsole Manager Spanning tree Features SpecificationsAccessories Status Indicators per port Boot and Configuration General IndicatorsConnector Interfaces Maximum Cabling Distances Power Cord Specifications Electrical SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling Index Get-bootpcommand Get-authcommandDatabase, switching Control commands Get-slipcommand Get-port-cfgcommand, 22Get-stpcommand Get-trapscommand MIB Set-commcommand Set-slipcommand Set-stpcommandXmt Transmit LED Troubleshooting Software updates Installation notes How to accessWorld Wide Web & Internet FTP Intel BBS