Get-lt-filter, Add-cf-entry | Intel 10/100 specs

C H A P T E R 3 Console Command Reference

SYS_console> get-lt-filter 00aa00a5898b

1200-AA-00-A5-89-8B LOCK_OFF SELF_OFF --- VIRTUAL LAN -----

SRC PORT to : MGMT P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12

================================================================

1	-	-	-	-	-	+	-	-	-	-	-	-	-
2	-	-	-	-	-	+	-	-	-	-	-	-	-
3	-	-	-	-	-	+	-	-	-	-	-	-	-
4	-	-	-	-	-	+	-	-	-	-	-	-	-
5	-	-	-	-	-	-	-	-	-	-	-	-	-
6	-	-	-	-	-	+	-	-	-	-	-	-	-
7	-	-	-	-	-	+	-	-	-	-	-	-	-
8	-	-	-	-	-	+	-	-	-	-	-	-	-
9	-	-	-	-	-	+	-	-	-	-	-	-	-
10	-	-	-	-	-	+	-	-	-	-	-	-	-
11	-	-	-	-	-	+	-	-	-	-	-	-	-
12	-	-	-	-	-	+	-	-	-	-	-	-	-

get-lt-filter

get-lt-filter <mac_address>

Displays the custom filter for the specified MAC address. See the previous example.

add-cf-entry

add-cf-entry {lock-onlock-offperm} <mac_address> <sport> <dport>

Adds a custom filter entry for the specified MAC address. lock-onindicates the entry won’t be aged out, but will be lost when the switch is reset. lock-offindicates the entry can be aged out normally. perm indicates the entry is written to NVRAM and remains after a reset.

sport is a hexadecimal representation of incoming ports, and dport is a hexadecimal bitmask representation of outgoing ports.

Packets arriving at the switch with the destination MAC address from any port specified in sport are transmitted to all ports specified in

dport.

SYS_console> add-cf-entry perm 00-AA-00-11-11-11 C C0 Add CF LT entry OK

CF Entry Update in NVRAM OK

This custom filter sends packets with destination MAC address

00-AA-00-11-11-11 from port 3 or 4 (hexadecimal C) to ports 6 and 7 (hexadecimal C0).

55

Image 58

Intel 10/100 manual Get-lt-filter, Add-cf-entry

Contents

User Guide First edition Contents Chapter Troubleshooting Check the LEDs for power and links Connect the network devices to the switchNext steps Optional Baud Data bits No parity Stop bit Xon/Xoff flow control Press Eand log into the Console Manager Topology Overview Installation and Setup Intel Express 10/100 Fast Ethernet Switch Xmt Using the SwitchPort status LEDs Rcv Management status LEDs Link UTP requirements Cabling RequirementsFiber optic requirements Straight-through vs. crossover cables NIC RJ-45 MDI Determining which cable to use Typical Configurations Configuring the mixed 10 Mbps workgroup environment Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches General rule for Repeater count limitationsOne repeater hop for Configuring Accessing the Console Manager Accessing the Console Manager remotely Entering commands Using the Console ManagerMeans you can type one of the following Vlan Console Manager command groups Procedures using this diagram Sample Console Manager Session To configure the Snmp agent Configuring the Snmp agent for IPCommands used Set the IP configuration. Type the command To configure a port for full duplex Configuring a port for full duplexRecommended environments Creating Virtual LANs VLANs To create an Svlan Create the two SVLANs. Type the commands To create a VBD Monitoring traffic To check traffic on a port Detecting congested segments Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting speed mismatches Statistic Definitions Configuring and Managing the Switch Group to display commands relevant to that group Reference Console Commands Console Command-line SummarySystem Commands IP Commands Snmp Commands Switching Database Commands Virtual LAN Vlan Commands Spanning Tree Commands Port Configuration Commands Switching Statistics Commands Banner Console CommandsHelp-kbd Logout Set-passwd System CommandsSys-stat Get-stst-level Warm-resetCold-reset Set-stst-level Get-sw-file Init-nvramSet-line-slip Set-sw-file Set-tftp-srvr Set-rsw-fileGet-tftp-srvr Sw-dnld IP Commands IP configuration Set-ip Get-bootpSet-bootp Set-ip-conf Set-slip-conf Get-slip-confSet-slip Get-gatew Ping-stop Ping CommandsPing Stops the active ping process. You can also press cC Add-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Del-arp-entry Get-comm Snmp CommandsSnmp community strings Set-comm Set-auth Snmp trap message commandsGet-auth Get-traps Del-trap Switching Database CommandsAdd-trap Removes a station from the trap table Database control commands Get-lt-entry Get-lt-16 FF-FF-FF-FF-FF-FF Del-lt-addr Find-lt-addrDel-lt-entry Add-lt-entry Get-lt-age Custom filteringSet-lt-age Get-lt-filter Add-cf-entry Get-nv-cftbl Vlan CommandsDel-cf-entry Displays the custom filter table stored in Nvram Get-con-matrix Get-vbc-matrix Get-vbc-tbl Set-vbc-domainDel-vbc-domain Set-sec-vlan Set-mon-port Get-svlan-tblDisplays the table of defined SVLANs Monitor Spanning Tree Commands Example Set-stp Get-stpGet-st-bcfg Get-st-syscfg Get-st-pcfgDisplays the spanning tree state for all ports Set-br-maxage Set-br-prioSet-br-hellot Set-prt-enb Set-br-fwdelSet-prt-prio Set-prt-pcost Displays the current port configuration Port Configuration CommandsUse these commands to configure and display port settings Get-port-cfg Set-speed-sel Statistics CommandsSet-port-dplex Set-port-fctrl Get-eth-cnt Get-colls-cnt Displays the Rmon statistics packet size histogram for port Get-rmon-cntGet-sdist-cnt Get-br-cnt 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Flow Control Problems Troubleshooting Intel Express 10/100 Fast Ethernet Switch Default Configuration System Console Manager Not installed see Accessories on nextPorts Spanning tree Accessories SpecificationsFeatures Status Indicators per port Connector Interfaces General IndicatorsBoot and Configuration Maximum Cabling Distances Electromagnetic Emissions and Safety Agency Approval Electrical SpecificationsPower Cord Specifications AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Index Displaying current state, 44 enabling or disabling Database, switching Get-authcommandGet-bootpcommand Control commands Get-stpcommand Get-port-cfgcommand, 22Get-slipcommand Get-trapscommand Set-commcommand MIB Set-stpcommand Set-slipcommandXmt Transmit LED How to access Troubleshooting Software updates Installation notesWorld Wide Web & Internet FTP Intel BBS