System Commands, Set-passwd, Sys-stat | Intel 10/100 specification

C H A P T E R 3 Console Command Reference

set-passwd

Changes the console password. The system first prompts you for the old password. You then type a new password and retype it for verification. Passwords never appear on the screen.

SYS_console> set-passwd

Enter old password:

Enter new password:

Enter new password again:

CLI running password changed

CLI password change in the NVRAM OK

If you enter the old password incorrectly or don’t verify the new password correctly, the password isn’t changed.

System Commands

sys-stat

Displays general status information about the switch and its SNMP agent hardware and software:

SYS_console>sys-stat

Intel Express 10/100 Fast Ethernet Switch

SNMP Agent Software - Version <version>

SNMP Object ID is : < .1.3.6.1.4.1.629.1.1.3 >

System MAC Address : 00-A0-C9-00-20-D9

Switching Data Base Size : 4096 entries

Total uptime(hundredths of seconds ): 111151888

Total uptime(days, hh:mm:ss format): 12 days, 20:45:18.88

i/f 1 -- description [ Port 1 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 2 -- description [ Port 2 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 3 -- description [ Port 3 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 4 -- description [ Port 4 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 5 -- description [ Port 5 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 6 -- description [ Port 6 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 7 -- description [ Port 7 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 8 -- description [ Port 8 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 9 -- description [ Port 9 - missing ] -- status [DOWN]

i/f 10 -- description [ Port 10 - missing ] -- status [DOWN] i/f 11 -- description [ Port 11 - missing ] -- status [DOWN] i/f 12 -- description [ Port 12 - missing ] -- status [DOWN]

39

Image 42

Intel 10/100 manual System Commands, Set-passwd, Sys-stat

Contents

User Guide First edition Contents Chapter Troubleshooting Connect the network devices to the switch Check the LEDs for power and linksNext steps Optional Baud Data bits No parity Stop bit Xon/Xoff flow control Press Eand log into the Console Manager Topology Overview Installation and Setup Intel Express 10/100 Fast Ethernet Switch Xmt Using the SwitchPort status LEDs Rcv Management status LEDs Link Cabling Requirements UTP requirementsFiber optic requirements Straight-through vs. crossover cables NIC RJ-45 MDI Determining which cable to use Typical Configurations Configuring the mixed 10 Mbps workgroup environment Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches Repeater count limitations General rule forOne repeater hop for Configuring Accessing the Console Manager Accessing the Console Manager remotely Using the Console Manager Entering commandsMeans you can type one of the following Vlan Console Manager command groups Procedures using this diagram Sample Console Manager Session To configure the Snmp agent Configuring the Snmp agent for IPCommands used Set the IP configuration. Type the command Configuring a port for full duplex To configure a port for full duplexRecommended environments Creating Virtual LANs VLANs To create an Svlan Create the two SVLANs. Type the commands To create a VBD Monitoring traffic To check traffic on a port Detecting congested segments Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting speed mismatches Statistic Definitions Configuring and Managing the Switch Group to display commands relevant to that group Reference Console Command-line Summary Console CommandsSystem Commands IP Commands Snmp Commands Switching Database Commands Virtual LAN Vlan Commands Spanning Tree Commands Port Configuration Commands Switching Statistics Commands Banner Console CommandsHelp-kbd Logout System Commands Set-passwdSys-stat Get-stst-level Warm-resetCold-reset Set-stst-level Get-sw-file Init-nvramSet-line-slip Set-sw-file Set-tftp-srvr Set-rsw-fileGet-tftp-srvr Sw-dnld IP Commands IP configuration Set-ip Get-bootpSet-bootp Set-ip-conf Set-slip-conf Get-slip-confSet-slip Get-gatew Ping-stop Ping CommandsPing Stops the active ping process. You can also press cC Add-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Del-arp-entry Get-comm Snmp CommandsSnmp community strings Set-comm Set-auth Snmp trap message commandsGet-auth Get-traps Del-trap Switching Database CommandsAdd-trap Removes a station from the trap table Database control commands Get-lt-entry Get-lt-16 FF-FF-FF-FF-FF-FF Del-lt-addr Find-lt-addrDel-lt-entry Add-lt-entry Custom filtering Get-lt-ageSet-lt-age Get-lt-filter Add-cf-entry Get-nv-cftbl Vlan CommandsDel-cf-entry Displays the custom filter table stored in Nvram Get-con-matrix Get-vbc-matrix Get-vbc-tbl Set-vbc-domainDel-vbc-domain Set-sec-vlan Set-mon-port Get-svlan-tblDisplays the table of defined SVLANs Monitor Spanning Tree Commands Example Get-stp Set-stpGet-st-bcfg Get-st-pcfg Get-st-syscfgDisplays the spanning tree state for all ports Set-br-prio Set-br-maxageSet-br-hellot Set-prt-enb Set-br-fwdelSet-prt-prio Set-prt-pcost Displays the current port configuration Port Configuration CommandsUse these commands to configure and display port settings Get-port-cfg Set-speed-sel Statistics CommandsSet-port-dplex Set-port-fctrl Get-eth-cnt Get-colls-cnt Displays the Rmon statistics packet size histogram for port Get-rmon-cntGet-sdist-cnt Get-br-cnt 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Flow Control Problems Troubleshooting Intel Express 10/100 Fast Ethernet Switch Default Configuration System Console Manager Not installed see Accessories on nextPorts Spanning tree Accessories SpecificationsFeatures Status Indicators per port Connector Interfaces General IndicatorsBoot and Configuration Maximum Cabling Distances Electromagnetic Emissions and Safety Agency Approval Electrical SpecificationsPower Cord Specifications AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Index Displaying current state, 44 enabling or disabling Database, switching Get-authcommandGet-bootpcommand Control commands Get-stpcommand Get-port-cfgcommand, 22Get-slipcommand Get-trapscommand Set-commcommand MIB Set-slipcommand Set-stpcommandXmt Transmit LED Troubleshooting Software updates Installation notes How to accessWorld Wide Web & Internet FTP Intel BBS