Ports, Not installed see Accessories on next | Intel 10/100 guide

A p p e n d i x

A Intel Express 10/100 Fast Ethernet Switch

Ports 1-8
Type:	10BASE-T/100BASE-TX (auto detecting),
	twisted-pair Ethernet (TPE)
Duplex mode:	Half
Flow control:	On

Ports 9-12

Not installed (see Accessories on next page)

Console Manager

Communications parameters: 9600 baud, 8-N-1

Login name: None

Password: None

Prompt: SYS_console>

Spanning tree
Spanning tree:	Enabled
Bridge priority:	32768	0-65535
Bridge max. age:	20	6.0-40.0 sec.
Bridge hello time:	2	1.0-10.0 sec.
Bridge forward delay: 15		4.0-30.0 sec.
Port priority:	128	0-255
Path cost:	100 (1000/LAN speed in Mbps). If a port is
	linked at 100 Mbps, the path cost is 10.

76

Image 79

Intel 10/100 manual Ports, Not installed see Accessories on next, Console Manager, Spanning tree

Contents

User Guide First edition Contents Chapter Troubleshooting Check the LEDs for power and links Connect the network devices to the switchNext steps Optional Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow control Overview Topology Intel Express 10/100 Fast Ethernet Switch Installation and Setup Rcv Using the SwitchPort status LEDs Xmt Link Management status LEDs UTP requirements Cabling RequirementsFiber optic requirements NIC RJ-45 MDI Straight-through vs. crossover cables Determining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical Configurations Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches General rule for Repeater count limitationsOne repeater hop for Configuring Accessing the Console Manager remotely Accessing the Console Manager Entering commands Using the Console ManagerMeans you can type one of the following Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagram Set the IP configuration. Type the command Configuring the Snmp agent for IPCommands used To configure the Snmp agent To configure a port for full duplex Configuring a port for full duplexRecommended environments To create an Svlan Creating Virtual LANs VLANs To create a VBD Create the two SVLANs. Type the commands Monitoring traffic To check traffic on a port Detecting speed mismatches Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting congested segments Statistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that group Console Commands Console Command-line SummarySystem Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database Commands Spanning Tree Commands Switching Statistics Commands Port Configuration Commands Logout Console CommandsHelp-kbd Banner Set-passwd System CommandsSys-stat Set-stst-level Warm-resetCold-reset Get-stst-level Set-sw-file Init-nvramSet-line-slip Get-sw-file Sw-dnld Set-rsw-fileGet-tftp-srvr Set-tftp-srvr IP configuration IP Commands Set-ip-conf Get-bootpSet-bootp Set-ip Get-gatew Get-slip-confSet-slip Set-slip-conf Stops the active ping process. You can also press cC Ping CommandsPing Ping-stop Del-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Add-arp-entry Set-comm Snmp CommandsSnmp community strings Get-comm Get-traps Snmp trap message commandsGet-auth Set-auth Removes a station from the trap table Switching Database CommandsAdd-trap Del-trap Get-lt-entry Database control commands FF-FF-FF-FF-FF-FF Get-lt-16 Add-lt-entry Find-lt-addrDel-lt-entry Del-lt-addr Get-lt-age Custom filteringSet-lt-age Add-cf-entry Get-lt-filter Displays the custom filter table stored in Nvram Vlan CommandsDel-cf-entry Get-nv-cftbl Get-vbc-matrix Get-con-matrix Set-sec-vlan Set-vbc-domainDel-vbc-domain Get-vbc-tbl Monitor Get-svlan-tblDisplays the table of defined SVLANs Set-mon-port Example Spanning Tree Commands Set-stp Get-stpGet-st-bcfg Get-st-syscfg Get-st-pcfgDisplays the spanning tree state for all ports Set-br-maxage Set-br-prioSet-br-hellot Set-prt-pcost Set-br-fwdelSet-prt-prio Set-prt-enb Get-port-cfg Port Configuration CommandsUse these commands to configure and display port settings Displays the current port configuration Set-port-fctrl Statistics CommandsSet-port-dplex Set-speed-sel Get-colls-cnt Get-eth-cnt Get-br-cnt Get-rmon-cntGet-sdist-cnt Displays the Rmon statistics packet size histogram for port 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control Problems Intel Express 10/100 Fast Ethernet Switch System Default Configuration Spanning tree Not installed see Accessories on nextPorts Console Manager Status Indicators per port SpecificationsFeatures Accessories Maximum Cabling Distances General IndicatorsBoot and Configuration Connector Interfaces AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Electrical SpecificationsPower Cord Specifications Electromagnetic Emissions and Safety Agency Approval Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling Index Control commands Get-authcommandGet-bootpcommand Database, switching Get-trapscommand Get-port-cfgcommand, 22Get-slipcommand Get-stpcommand MIB Set-commcommand Set-stpcommand Set-slipcommandXmt Transmit LED How to access Troubleshooting Software updates Installation notesWorld Wide Web & Internet FTP Intel BBS