Get-rmon-cnt, Get-sdist-cnt, Get-br-cnt | Intel 10/100 instruction

C H A P T E R 3

Intel Express 10/100 Fast Ethernet Switch

get-rmon-cnt

get-rmon-cnt <port>

Displays the remote monitoring (RMON) statistics group 1 counters for port.

SYS_console> get-rmon-cnt 1 Ethernet RMON Counters for port 1

====================================================

etherStatsOctets	: 942514513
etherStatsPkts	:	2900281
etherStatsBcastPkts	:	0
etherStatsMcastPkts	:	0
etherStatsCRCAllignPkts:		0
etherStatsUndersizePkts:		0
etherStatsOversizePkts :		0
etherStatsRuntPkts	:	4
etherStatsJabberPkts	:	0
etherStatsCollisions	:	36

get-sdist-cnt

get-sdist-cnt <port>

Displays the RMON statistics packet size histogram for port.

SYS_console> get-sdist-cnt 1

RMON Packet Size Distribution Counters for port 1

============================================================

etherStatsPkts64Octets	:	678664
etherStatsPkts65to127Octets	:	1634637
etherStatsPkts128to255Octets	:	42062
etherStatsPkts256to511Octets	:	27590
etherStatsPkts512to1023Octets	:	49248
etherStatsPkts1024to1518Octets :		470762

get-br-cnt

get-br-cnt <port-number>

Displays the switching statistics counters for a port. The command displays the number of:

•frames or bytes received.

•frames forwarded.

•multicast frames.

•frames with unknown destination and subsequently multicast.

•frames transmitted.

68

Image 71

Intel 10/100 manual Get-rmon-cnt, Get-sdist-cnt, Displays the Rmon statistics packet size histogram for port, Get-br-cnt

Contents

User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow control Overview Topology Intel Express 10/100 Fast Ethernet Switch Installation and Setup Rcv Using the SwitchPort status LEDs Xmt Link Management status LEDs Fiber optic requirements Cabling RequirementsUTP requirements NIC RJ-45 MDI Straight-through vs. crossover cables Determining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical Configurations Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager remotely Accessing the Console Manager Means you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagram Set the IP configuration. Type the command Configuring the Snmp agent for IPCommands used To configure the Snmp agent Recommended environments Configuring a port for full duplexTo configure a port for full duplex To create an Svlan Creating Virtual LANs VLANs To create a VBD Create the two SVLANs. Type the commands Monitoring traffic To check traffic on a port Detecting speed mismatches Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting congested segments Statistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that group System Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database Commands Spanning Tree Commands Switching Statistics Commands Port Configuration Commands Logout Console CommandsHelp-kbd Banner Sys-stat System CommandsSet-passwd Set-stst-level Warm-resetCold-reset Get-stst-level Set-sw-file Init-nvramSet-line-slip Get-sw-file Sw-dnld Set-rsw-fileGet-tftp-srvr Set-tftp-srvr IP configuration IP Commands Set-ip-conf Get-bootpSet-bootp Set-ip Get-gatew Get-slip-confSet-slip Set-slip-conf Stops the active ping process. You can also press cC Ping CommandsPing Ping-stop Del-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Add-arp-entry Set-comm Snmp CommandsSnmp community strings Get-comm Get-traps Snmp trap message commandsGet-auth Set-auth Removes a station from the trap table Switching Database CommandsAdd-trap Del-trap Get-lt-entry Database control commands FF-FF-FF-FF-FF-FF Get-lt-16 Add-lt-entry Find-lt-addrDel-lt-entry Del-lt-addr Set-lt-age Custom filteringGet-lt-age Add-cf-entry Get-lt-filter Displays the custom filter table stored in Nvram Vlan CommandsDel-cf-entry Get-nv-cftbl Get-vbc-matrix Get-con-matrix Set-sec-vlan Set-vbc-domainDel-vbc-domain Get-vbc-tbl Monitor Get-svlan-tblDisplays the table of defined SVLANs Set-mon-port Example Spanning Tree Commands Get-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-prt-pcost Set-br-fwdelSet-prt-prio Set-prt-enb Get-port-cfg Port Configuration CommandsUse these commands to configure and display port settings Displays the current port configuration Set-port-fctrl Statistics CommandsSet-port-dplex Set-speed-sel Get-colls-cnt Get-eth-cnt Get-br-cnt Get-rmon-cntGet-sdist-cnt Displays the Rmon statistics packet size histogram for port 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control Problems Intel Express 10/100 Fast Ethernet Switch System Default Configuration Spanning tree Not installed see Accessories on nextPorts Console Manager Status Indicators per port SpecificationsFeatures Accessories Maximum Cabling Distances General IndicatorsBoot and Configuration Connector Interfaces AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Electrical SpecificationsPower Cord Specifications Electromagnetic Emissions and Safety Agency Approval Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling Index Control commands Get-authcommandGet-bootpcommand Database, switching Get-trapscommand Get-port-cfgcommand, 22Get-slipcommand Get-stpcommand MIB Set-commcommand Xmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access