Port Configuration Commands, Get-port-cfg | Intel 10/100 specs

C H A P T E R 3 Console Command Reference

NOTE

Setting a port to full duplex automatically disables flow control. Since collisions don’t happen on a full-duplex link, flow control isn’t possible.

One exception is between two Express 10/100 switches. A special piece of information is added to packets traveling between switches to accom- plish this.

Port Configuration Commands

Use these commands to configure and display port settings.

get-port-cfg

Displays the current port configuration.

SYS_console> get-port-cfg
PORT_ID LAN_TYPE LINK IF_TYPE SPEED_SEL LAN_SPEED	FDPLX FCTRL

======================================================================

1	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
2	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
3	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
4	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
5	ETH10/100	ON	TPFD	ASENSE	10Mbps	OFF	ON
6	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
7	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
8	ETH10/100	OFF	TPFD	ASENSE	10Mbps	OFF	ON
9	NONE	---- PORT NOT INSTALLED ----
10	NONE	---- PORT NOT INSTALLED ----
11	NONE	---- PORT NOT INSTALLED ----
12	NONE	---- PORT NOT INSTALLED ----

The command displays the following information for each port:

•LAN type: ETH10/100 indicates the port can operate at 10 or 100 Mbps.

•Link status: ON or OFF.

•Physical interface type: TPFD indicates Twisted-pair (TP) Ethernet, Full Duplex (FD) capable.

•Speed select: ASENSE indicates the port auto-negotiates with the device on the other end.

•LAN Speed: LAN_SPEED indicates the speed of the link. By default, all ports are 10 Mbps when no device is attached.

•Full duplex mode: ON or OFF (default).

•Flow control: ON (default) or OFF. If you set a port to full duplex, flow control is automatically turned off (changes take effect after a reset). If you try to set flow control to ON while full duplex is selected, the Console Manager ignores the change on reset.

65

Image 68

Intel 10/100 manual Port Configuration Commands, Use these commands to configure and display port settings, Get-port-cfg

Contents

User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Baud Data bits No parity Stop bit Xon/Xoff flow control Press Eand log into the Console Manager Topology Overview Installation and Setup Intel Express 10/100 Fast Ethernet Switch Using the Switch Port status LEDsXmt Rcv Management status LEDs Link Fiber optic requirements Cabling RequirementsUTP requirements Straight-through vs. crossover cables NIC RJ-45 MDI Determining which cable to use Typical Configurations Configuring the mixed 10 Mbps workgroup environment Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager Accessing the Console Manager remotely Means you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Procedures using this diagram Sample Console Manager Session Configuring the Snmp agent for IP Commands usedTo configure the Snmp agent Set the IP configuration. Type the command Recommended environments Configuring a port for full duplexTo configure a port for full duplex Creating Virtual LANs VLANs To create an Svlan Create the two SVLANs. Type the commands To create a VBD Monitoring traffic To check traffic on a port Detecting faulty adapters or hub ports Detecting bad or poor quality cableDetecting congested segments Detecting speed mismatches Statistic Definitions Configuring and Managing the Switch Group to display commands relevant to that group Reference System Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Switching Database Commands Virtual LAN Vlan Commands Spanning Tree Commands Port Configuration Commands Switching Statistics Commands Console Commands Help-kbdBanner Logout Sys-stat System CommandsSet-passwd Warm-reset Cold-resetGet-stst-level Set-stst-level Init-nvram Set-line-slipGet-sw-file Set-sw-file Set-rsw-file Get-tftp-srvrSet-tftp-srvr Sw-dnld IP Commands IP configuration Get-bootp Set-bootpSet-ip Set-ip-conf Get-slip-conf Set-slipSet-slip-conf Get-gatew Ping Commands PingPing-stop Stops the active ping process. You can also press cC Address Resolution Protocol ARP Commands Get-arp-tblAdd-arp-entry Del-arp-entry Snmp Commands Snmp community stringsGet-comm Set-comm Snmp trap message commands Get-authSet-auth Get-traps Switching Database Commands Add-trapDel-trap Removes a station from the trap table Database control commands Get-lt-entry Get-lt-16 FF-FF-FF-FF-FF-FF Find-lt-addr Del-lt-entryDel-lt-addr Add-lt-entry Set-lt-age Custom filteringGet-lt-age Get-lt-filter Add-cf-entry Vlan Commands Del-cf-entryGet-nv-cftbl Displays the custom filter table stored in Nvram Get-con-matrix Get-vbc-matrix Set-vbc-domain Del-vbc-domainGet-vbc-tbl Set-sec-vlan Get-svlan-tbl Displays the table of defined SVLANsSet-mon-port Monitor Spanning Tree Commands Example Get-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-br-fwdel Set-prt-prioSet-prt-enb Set-prt-pcost Port Configuration Commands Use these commands to configure and display port settingsDisplays the current port configuration Get-port-cfg Statistics Commands Set-port-dplexSet-speed-sel Set-port-fctrl Get-eth-cnt Get-colls-cnt Get-rmon-cnt Get-sdist-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Flow Control Problems Troubleshooting Intel Express 10/100 Fast Ethernet Switch Default Configuration System Not installed see Accessories on next PortsConsole Manager Spanning tree Specifications FeaturesAccessories Status Indicators per port General Indicators Boot and ConfigurationConnector Interfaces Maximum Cabling Distances Electrical Specifications Power Cord SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Index Displaying current state, 44 enabling or disabling Get-authcommand Get-bootpcommandDatabase, switching Control commands Get-port-cfgcommand, 22 Get-slipcommandGet-stpcommand Get-trapscommand Set-commcommand MIB Xmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access