Connect the network devices to the switch | Intel 10/100 manual

Quick Start

1.Install the Express 10/100 Switch in a rack or on a shelf or table and plug the cord in. If you’re in Europe or Asia, or any other country that has a 220-volt electrical system, set the power supply switch to 230 (115 is the default). Otherwise, leave the switch set to 115. Turn the power on.

Brackets and screws for standard 19-inch equipment rack placement.

Rubber feet for shelf or table placement.

2. Connect the network devices to the switch.

Cabling Guidelines

				at 10 Mbps	at 100 Mbps

			Server/	CAT 3, 4, or 5	CAT 5
			Workstation	straight-through	straight-through
			to Switch
	Crossover cables	Straight-through cables	Hub to	CAT 3, 4, or 5	CAT 5 crossover
	to hubs or other	Straight-through cables	Switch	crossover
		to servers/workstations.	Switch	crossover

	switches.		Switch to	CAT 3, 4, or 5	CAT 5 crossover
	switches.		Switch to	CAT 3, 4, or 5	CAT 5 crossover
			Switch	crossover

3. Check the LEDs for power and links.

Lights when a

device is attached.

Always on.

Lights briefly while the switch performs self-tests.

Blinks every two seconds.

Lights when a 100BASE-TX device is attached.

Next steps (Optional)

•Continue to the next page if you want to configure the switch to work with an SNMP-compliant Network Management System (NMS).

•See Chapter 2 if you want to use the Console Manager to change port configurations (set a port for full duplex or manually set the speed), assign an IP address, or check port statistics.

1

Image 5

Intel 10/100 manual Connect the network devices to the switch, Check the LEDs for power and links, Next steps Optional

Contents

User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow control Overview Topology Intel Express 10/100 Fast Ethernet Switch Installation and Setup Port status LEDs Using the SwitchXmt Rcv Link Management status LEDs Fiber optic requirements Cabling RequirementsUTP requirements NIC RJ-45 MDI Straight-through vs. crossover cables Determining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical Configurations Configuration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager remotely Accessing the Console Manager Means you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagram Commands used Configuring the Snmp agent for IPTo configure the Snmp agent Set the IP configuration. Type the command Recommended environments Configuring a port for full duplexTo configure a port for full duplex To create an Svlan Creating Virtual LANs VLANs To create a VBD Create the two SVLANs. Type the commands Monitoring traffic To check traffic on a port Detecting bad or poor quality cable Detecting faulty adapters or hub portsDetecting congested segments Detecting speed mismatches Statistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that group System Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database Commands Spanning Tree Commands Switching Statistics Commands Port Configuration Commands Help-kbd Console CommandsBanner Logout Sys-stat System CommandsSet-passwd Cold-reset Warm-resetGet-stst-level Set-stst-level Set-line-slip Init-nvramGet-sw-file Set-sw-file Get-tftp-srvr Set-rsw-fileSet-tftp-srvr Sw-dnld IP configuration IP Commands Set-bootp Get-bootpSet-ip Set-ip-conf Set-slip Get-slip-confSet-slip-conf Get-gatew Ping Ping CommandsPing-stop Stops the active ping process. You can also press cC Get-arp-tbl Address Resolution Protocol ARP CommandsAdd-arp-entry Del-arp-entry Snmp community strings Snmp CommandsGet-comm Set-comm Get-auth Snmp trap message commandsSet-auth Get-traps Add-trap Switching Database CommandsDel-trap Removes a station from the trap table Get-lt-entry Database control commands FF-FF-FF-FF-FF-FF Get-lt-16 Del-lt-entry Find-lt-addrDel-lt-addr Add-lt-entry Set-lt-age Custom filteringGet-lt-age Add-cf-entry Get-lt-filter Del-cf-entry Vlan CommandsGet-nv-cftbl Displays the custom filter table stored in Nvram Get-vbc-matrix Get-con-matrix Del-vbc-domain Set-vbc-domainGet-vbc-tbl Set-sec-vlan Displays the table of defined SVLANs Get-svlan-tblSet-mon-port Monitor Example Spanning Tree Commands Get-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-prt-prio Set-br-fwdelSet-prt-enb Set-prt-pcost Use these commands to configure and display port settings Port Configuration CommandsDisplays the current port configuration Get-port-cfg Set-port-dplex Statistics CommandsSet-speed-sel Set-port-fctrl Get-colls-cnt Get-eth-cnt Get-sdist-cnt Get-rmon-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt 2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control Problems Intel Express 10/100 Fast Ethernet Switch System Default Configuration Ports Not installed see Accessories on nextConsole Manager Spanning tree Features SpecificationsAccessories Status Indicators per port Boot and Configuration General IndicatorsConnector Interfaces Maximum Cabling Distances Power Cord Specifications Electrical SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Snmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling Index Get-bootpcommand Get-authcommandDatabase, switching Control commands Get-slipcommand Get-port-cfgcommand, 22Get-stpcommand Get-trapscommand MIB Set-commcommand Xmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access