Manuals / Brands / Computer Equipment / Network Card / Intel / Computer Equipment / Network Card

Intel 82555 11.4.6 Jabber Timing Parameters , 11.4.7 Receive Packet Timing Parameters

1 58

Download 58 pages, 863.99 Kb

Datasheet 49

Networking Silicon — 82555

11.4.6 Jabber Timing Parameters 11.4.7 Receive Packet Timing Parameters

Figure 20. Squelch Test Timing Parameters

TXEN

COL

TXCLK

T20 T21

Symbol Parameter Conditions Min Typ Max Units

T22 TJAB_ON

Jabber turn-on delay (TXEN

asserted to end of transmit

frame) 10 Mbps 26 ms

T23 TJAB_OFF Jabber turn-off delay (TXEN de-

asserted to falling edge of COL) 10 Mbps 410 ms

Figure 21. Jabber Timing Parameters

TXEN

COL

TDP/TDN

T22

T23

Symbol Parameter Conditions Min Typ Max Units

T24 TR_CRSH Start of receive frame to rising

edge of CRS 100 Mbps 11 13 bits

T24a TR_CRSH Start of receive frame to rising

edge of CRS 10 Mbps 3 5 bits

T25 TR_RXDVH Start of receive frame to rising

edge of RXDV 100 Mbps 15 bits

T25a TR_RXDVH Start of receive frame to rising

edge of RXDV 10 Mbps 22 bits

T26 TR_CRSL End of receive frame to falling

edge of CRS 100 Mbps 14 16 bits

Contents

Main 82555 10/100 Mbps LAN Physical Layer Interface Networking Silicon Datasheet Product Features Page Page Contents 1.0 Introduction 1.1 Functional Overview 1.2 Compliance to Industry Standards Page 2.0 Architectural Overview 2.1 100 Mbps Mode 2.2 10 Mbps Mode Magnetics Module Datasheet 5 g Figure 4. Intel 82557/82555 Solution 2.3 Media Independent Interface (MII) 82555 82557 PCI Bus Si nals Page Page 8 Datasheet 3.1 Pin Types 3.2 Clock Pins 3.4 Media Independent Interface (MII) Pins 3.3 Twisted Pair Ethernet (TPE) Pins 3.5 Media Access Control/Repeater Interface Control Pins Datasheet 9 10 Datasheet 3.6 LED Pins 3.7 External Bias Pins Datasheet 11 3.8 Miscellaneous Control Pins 3.9 Power and Ground Pins 4.0 100BASE-TX Adapter Mode Operation 4.1 100BASE-TX Transmit Clock Generation 4.2 100BASE-TX Transmit Blocks 4.2.1 100BASE-TX 4B/5B Encoder 4.2.2 100BASE-TX Scrambler and MLT-3 Encoder Page 4.2.4 Transmit Driver 4.3 100BASE-TX Receive Blocks 4.4 100BASE-TX Collision Detection 4.5 100BASE-TX Link Integrity and Auto-Negotiation Solution 4.5.1 Link Integrity 4.5.2 Auto-Negotiation 4.5.3 Combination Tx/T4 Auto-Negotiation Solution 4.6 Auto 10/100 Mbps Speed Selection 4.7 Adapter Mode Addresses Page 5.0 10BASE-T Functionality in Adapter Mode 5.1 10BASE-T Transmit Clock Generation 5.2 10BASE-T Transmit Blocks 5.2.1 10BASE-T Manchester Encoder 5.2.2 10BASE-T Driver and Filter 5.4 10BASE-T Collision Detection 5.5 10BASE-T Link Integrity 5.6 10BASE-T Jabber Control Function Page Page 6.0 Repeater Mode 6.1 Special Repeater Features 6.2 Connectivity Page 7.0 Management Data Interface 7.1 MDI Frame Structure 7.2 MDI Registers 7.2.1 MDI Registers 0 - 7 7.2.1.1 Register 0: Control Register Bit Definitions 7.2.1.2 Register 1: Status Register Bit Definitions Datasheet 29 30 Datasheet Datasheet 31 7.2.1.6 Register 5: Auto-Negotiation Link Partner Ability Register Bit Definitions Register numbers 16, 17, 20, 21, 22, 23, 24, 25, and 27 are described in the following subsections. 7.2.1.7 Register 6: Auto-Negotiation Expansion Register Bit Definitions 7.2.2 MDI Registers 8 - 15 Registers eight through fifteen are reserved for IEEE. 7.2.3 MDI Registers 16 - 31 32 Datasheet 7.2.3.1 Register 16: 82555 Status and Control Register Bit Definitions 7.2.3.2 Register 17: 82555 Special Control Bit Definitions Datasheet 33 7.2.3.3 Register 20: 100BASE-TX Receive Disconnect Counter Bit Definitions 7.2.3.4 Register 21: 100BASE-TX Receive Error Frame Counter Bit Definitions 34 Datasheet 7.2.3.5 Register 22: Receive Symbol Error Counter Bit Definitions 7.2.3.6 Register 23: 100BASE-TX Receive Premature End of Frame Error Counter Bit Definitions 7.2.3.9 Register 27: 82555 Special Control Bit Definitions 7.2.3.7 Register 24: 10BASE-T Receive End of Frame Error Counter Bit Definitions 7.2.3.8 Register 25: 10BASE-T Transmit Jabber Detect Counter Bit Definitions 8.0 Auto-Negotiation Functionality 8.1 Description 8.2 Parallel Detect and Auto-Negotiation Page Page 9.0 LED Descriptions Page 10.0 Reset and Miscellaneous Test Modes 10.1 Reset 10.2 Loopback 10.3 Scrambler Bypass 10.4 Test Port Page Datasheet 43 11.0 Electrical Specifications and Timing Parameters 11.1 Absolute Maximum Ratings 11.3.2 10BASE-T Voltage/Current DC Characteristics 11.2 General Operating Conditions 11.3 DC Characteristics 11.3.1 MII DC Characteristics Icct10 105mA 110mA 115mA Figure 11. RBIAS10 Resistance versus I 44 Datasheet 768 Icct100 38mA 40mA 42mA 604 634 Figure 12. RBIAS100 Resistance versus I 11.4.2 MII Timing Parameters T1,T2,T3 Figure 15. MII Transmit Timing Parameters Figure 14. MII Clocks AC Timing 46 Datasheet 11.4.3 Repeater Mode Timing Parameters Datasheet 47 Figure 16. MII Receive Timing Parameters Figure 18. PORT Enable Timing Figure 17. MII Timing Parameters: MDC/MDIO 11.4.4 Transmit Packet Timing Parameters Figure 19. Transmit Frame Timing Parameters 11.4.5 Squelch Test Timing Parameters Datasheet 49 Figure 20. Squelch Test Timing Parameters 11.4.6 Jabber Timing Parameters 11.4.7 Receive Packet Timing Parameters 50 Datasheet Figure 22. Receive Packet Timing Parameters 11.4.8 10BASE-T Normal Link Pulse (NLP) Timing Parameters 11.4.9 Auto-Negotiation Fast Link Pulse (FLP) Timing Parameters Figure 23. Normal Link Pulse Timing Parameters Datasheet 51 Networking Silicon 82555 11.4.10 Reset Timing Parameters 11.4.11 X1 Clock Specifications 11.4.12 100BASE-TX Transmitter AC Specification 12.0 82555 Package Information