ITT SSV - page 6

2. MAXIMUM INLET PRESSURE

The following table shows the maximum permissible

inlet pressure. However, the actual inlet pressure +

pressure against a closed valve must always be lower

than the maximum permissible operating pressure.

Pump Number Maximum

of Stages Inlet Pressure

1SV 2-16 Stages 250 psi (17 bar)

17-22 Stages 250 psi (17 bar)

2SV 2-15 Stages 250 psi (17 bar)

16-22 Stages 250 psi (17 bar)

3SV 2-13 Stages 250 psi (17 bar)

14-16 Stages 250 psi (17 bar)

4SV 2-10 Stages 250 psi (17 bar)

11-12 Stages 250 psi (17 bar)

33SV 1-10 Stages

46SV 1-10 Stages 250 psi (17 bar)

66SV 1-6 Stages

92SV 1-6 Stages

3. MAXIMUM OPERATING PRESSURE

(staging at 3500 RPM)

Series At 250º F PSI / Bar

1SV 2-16 Stages 325 / 25

17-22 Stages 580 / 40

2SV 2-15 Stages 325 / 25

16-22 Stages 580 / 40

3SV 2-13 Stages 325 / 25

14-16 Stages 580 / 40

4SV 2-10 Stages 325 / 25

11-12 Stages 580 / 40

33SV 1-6 Stages 362 / 25

7-10 Stages 580 / 40

46SV 1-5 Stages 362 / 25

6-10 Stages 580 / 40

66SV 1-5 Stages 362 / 25

6 Stages 580 / 40

92SV 1-5 Stages 362 / 25

NOTE: Oval ﬂange (1-3SV) maximum working

pressure is 232 psi (16 bar).

4. TEMPERATURE CAPABILITY

The SSV pump is capable of pumping liquids within

the below temperature range:

1-4SV -22º F to 250º F (-30º C to 120º C)

33SV-92SV -22º F to 250º F (-30º C to 120º C)

NOTE: In order to provide adequate cooling for the

electric motor, the ambient temperature must

be 32º F to 104º F and the relative humidity at

104º F must not exceed 50%.

For temperatures above 104º F and for installations

sites located at elevation in excess at 3000 feet above

sea level it may be necessary to derate the motor

performance. Please contact your distributor/dealer for

assistance.

WARNING

5. MINIMUM NOMINAL FLOW RATE

To prevent overheating of the internal pump com-

ponents, make sure that a minimum water ﬂow is

always guaranteed when the pump is running.

For continuous operation the minimum ﬂow rate

recommended is speciﬁed below.

Pump Size 1SV 2SV 3SV 4SV

Min. Flow 3500 RPM 3 6 12 17

(gpm) 2900 RPM 3 6 10 14

Pump Size 33SV 46SV 66SV 92SV

Min. Flow 3500 RPM 35 40 70 100

(gpm) 2900 RPM 8 10 14 20

NOTE: If this cannot be archived, then a bypass/

recirculate line is recommended.

Do not run the pump against a closed

discharge for longer than a few seconds.

6. NUMBER OF STARTS PER HOUR

For electric pumps coupled to motors supplied by

Goulds Pumps, the maximum number of work cycles

(starts and stops) in one hour are as follows:

HP 3/4-3 5-10 15-20 25-75

# of Starts 5 5 5 5

For more details, refer to technical manual.

If you use a different motor from

the standard one supplied by Goulds

Pumps, please consult with the motor manufacturer

to ﬁnd out the maximum number of work cycles

allowed.

7. POWER SUPPLY REQUIREMENTS

Make sure that the supply voltages

and frequencies are suited to the

characteristics of the electric motor. Check the

motor rating plate.

In general, the supply voltage tolerances for motor

operation are as follows:

Hz Phase V ±%

60 1 230 10

60 3 230 / 460 10

60 3 460 10

1. TRANSPORTATION AND HANDLING OF

PACKED PRODUCT

The SSV pump is packed in cartons or wooden

crates having different dimensions and shapes.

Some cartons (the supporting base

is made of wood) are designed to be

transported and handled in the vertical position.

Other cartons, as well as the wooden crates, are

designed to be transported and handled in the hori-

zontal position. Protect the product against humid-

ity, heat sources and mechanical damage (collisions,

falls, ...). Do not place heavy weights on the cartons.

WARNING