TIME CODE | – Presetting the time code – |
Variable values can be set for the time code and the userÕs bit for efficient material management and editing.
| DISP/8 button | RESET button |
|
| OPERATE |
Mini | MENU DISP RESET | A.DUB REC PLAY PAUSE |
|
|
|
|
| PROFESSIONAL |
|
|
|
|
|
; button | SEARCH– | SET | SEARCH+ |
|
|
|
|
|
| |
|
|
|
|
| EJECT |
| REW | STOP | FF | |
| MIC | HOLD | BLANK | CUE UP |
|
|
|
|
|
|
| PHONES | REC LEVEL |
|
|
| AUDIO | INPUT | REMOTE | ||
|
|
|
|
|
| COUNTER MONITOR OUTPUT SELECT | ||||
|
|
|
|
|
| CTL | L | DV |
| |
|
|
|
|
|
| TC | MIX | MIX | LINE |
|
|
|
| UB | R | Y/C | LOCAL | ||||
|
|
|
|
|
| (CPN) | ||||
HOLD button | 9 button | : button | COUNTER switch | |||||||
TC/UB/CLOCK(1/2) Menu screen
Ð Ð Ð T C / U B / C L O C K ( 1 / 2 )Ð Ð Ð
T C G S O U R C E | I N T E R N A L | |
T C G S E L E C T | P R E S E T | |
T C G M O D E | R E C - R U N | |
N D F / D F ( N T S C ) | Ð Ð Ð | |
D F B I T ( P A L ) | O N | |
T C D U P L I C A T E | O F F | |
T C O F F S E T | O F F | |
N E X T | P A G E |
|
P A G E | B A C K |
|
:Setting: ...TC/UB/CLOCK(1/2) Menu screen
Set TCG SOURCE to “INTERNAL”.
Set TCG SELECT to “PRESET”.
TCG MODE:
: The time code runs only during recording. | |
| : The time code runs from the point when the preset |
| is completed. |
❈In the case of the userÕs bit, setting is not required.
LCD display
CH1/3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OVER |
48k L | 40 30 | 20 | 10 |
|
|
| 0 dB | |||||||||||
CH2/4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OVER | |
RRUN H M S F
NDF TC 00 00 00 00
STOP | SP222min |
| |||
e | |||||
|
|
| 01/02/03 | Y/C SYNC |
|
|
|
| CF | ||
|
|
| AM 01:23:45 |
| r |
Memo
●To stop the setting, press the HOLD button to return to the normal screen.
●To preset all digits to 0, press the RESET button when any of the digits is blinking.
●When the hour digit is blink- ing, the frame digit starts blinking when the ; button is pressed.
●If a userÕs bit is input with its all digits set as ÒFÓ,
NDF/DF (NTSC):
NON DROP :
of frame is more important.
DROP : Drop frame mode. Use this setting if the recording time is more important.
:Operation: ... Perform setting while checking the LCD display.
This section describes the setting of the time code. The setting of the userÕs bit is the same. Values that can be used to configure the userÕs bit are hexadecimal numeral from 0 Ð F.
1. Set the counter switch to TC.
(For userÕs bit, set the switch to UB.)
2. Press the DISP button to change the LCD to its enlarged dis- play mode.
3. In the STOP mode, press the HOLD button.
¥The hour digit of the counter starts blinking.
4.Press the 8 or 9 button to change the value.
5.Press the : or ; button to move blinking to the next digit.
6.Press the 8 or 9 button to change the value of the blinking digit.
7.Repeat steps 5 and 6 to perform the necessary settings.
8.Press the SET button to confirm the setting value and blink- ing of the counter stops.
59
