JVC BR-DV6000U  Setup preset commands,
First byte Bit No Status If the bit is,
Second byte

DD: JVC STATUS SENSE

This section describes 4-byte data that are returned when the STATUS SENSE command is sent.

First byte

Bit No.		Status: If the bit is 1
7	Always 1
6	Always 0
5	Unused	: Always 0
4	DMF	: Playing back LP-mode tape
3	Unused	: Always 0
2	JVC TABLE2	: JVC TABLE 2 enabled
1	JVC TABLE1	: JVC TABLE 1 enabled.
0	LOCAL	: REMOTE switch set to LOCAL

Second byte

Bit	No.	Status: If the bit is 1
	7	TC GENERATOR	: Time code generator in the TCG
			mode.
	6	USER BIT	: Counter mode set to the UB
			mode.
	5	TIME CODE	: Counter mode set to the TC
			mode.
	4	CONTROL PULSE	: Counter mode set to the CTL
			mode.
	3	CTL completion	: Always 0
	2	DROP FRAME	: Current time code in the DROP
			FRAME mode
	1	LTC	: Always 1
	0	Unused	: Always 0
Third byte
Bit	No.	Status: If the bit is 1
	7	TC REC RUN	: TCG set to the Rec Run mode
	6	TC REGEN	: TCG set to the REGENERATION
			mode
	5	TC EXTERNAL	: TCG set to the EXT mode
	4	TC INSERT LED	: Time code insert edit mode
	3	AUD1 INSERT LED	: Audio-1/2 insert edit mode
	2	AUD2 INSERT LED	: Audio-3/4 insert edit mode
	1	VIDEO INSERT LED:Video insert edit mode
	0	ASSEM	: Assemble mode
Fourth byte
Bit	No.	Status: If the bit is 1
	7	TBC PWB IN	: Always 1
	6	TC PWB IN	: Always 1
	5	DA3 INSERT LED	: Always 0
	4	DA4 INSERT LED	: Always 0
	3	AUTO MODE	: Auto editing/Previewing/Review-
			ing
	2	Unused	: Always 0
	1	Unused	: Always 0
	0	Unused	: Always 0

Setup (preset) commands

These commands are for setting various types of VCR data. The commands corresponding to the settings can be transmitted.

Table	Command		Description
B	E0	TC DATA PRESET :
		For presetting the time code data. To
		set, transmit the time data following
		this command. Specify the time in or-
		der of hour, minute, second and frame,
		using two digits for each. When EN-
		TER (40h) is transmitted before all dig-
		its have been transmitted, the time
		code data are specified by entering
		digits from the uppermost digit.
B	E1	TC UB DATA PRESET :
		For presetting the userÕs bit.
	E3	IN DATA PRESET :
		For presetting the edit-in point. Set by
		transmitting time data following this
		command.
		Specify the time in order of hour,
		minute, second and frame, using two
		digits for each.
		If ENTER (40h) is transmitted before
		all digits have been transmitted, this
		command is executed with unspecified
		parts set as Ò0.Ó
		If this is a negative value in the CTL
		mode, set 38h to the digit of 10H.
	E4	OUT DATA PRESET :
		For presetting the edit-out point.
		For details, refer to IN DATA PRESET
		(E3h) above.
B	E5	EDIT PRESET :
		For selecting the edit mode. Each bit
		is defined as shown in the table be-
		low.
			7	6	5		4
		First	0	0	1		1
			3	2	1		0
		byte	0	INS	ASM	Video
		Second	0	0	1		1
			3	2	1		0
		byte	0	TC	Aud-1	Aud-2
		¥ ENTER (40h) is invalid.
B	E6	PREROLL TIME PRESET :
		For setting the preroll time. Specify this
		by transmitting 2-byte data following
		this command. First byte for tenÕs place
		and second byte for oneÕs place.

91