16 EN INSTALLING YOUR NEW UNIT
Basic Connection |
|
|
|
|
| THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO | ||||||||||||||
|
|
|
|
| OPERATION CAN BE PERFORMED. | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | Make sure the package contains all of the accessories listed in | |
|
|
|
|
|
|
|
|
|
|
|
|
| Antenna or Cable | 2 | “SPECIFICATIONS” (A pg. 69). | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| Place the unit on a stable, horizontal surface. | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | Connect the unit to a TV depending on the TV and cables you | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| Coaxial cable |
|
|
|
|
|
| use. | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 8 | Simple Connections | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| To connect to TV’s VIDEO input and AUDIO input connectors ^ | |
|
|
|
|
|
|
|
|
|
|
|
|
| Flat feeder |
|
| A Disconnect the TV aerial cable from the TV. | ||||
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| B Connect the TV antenna cable to the [ANTENNA IN] connector | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| on the rear panel of the unit. |
| Matching transformer (not |
|
|
|
|
|
| |||||||||||||
| AC Outlet |
| C Connect the [ANTENNA OUT] connector on the rear panel of | |||||||||||||||||
To | supplied) |
|
|
|
|
|
| the unit and the TV’s antenna connector with the supplied RF | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
[ANTENNA IN] |
|
|
|
|
|
|
|
|
|
| AC Power Cord |
|
| cable. | ||||||
|
|
|
|
|
|
|
|
|
|
|
| D Connect the supplied video/audio cable between the [VIDEO/ | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
AUDIO OUTPUT] connectors on the rear panel of the unit and the TV’s VIDEO/AUDIO input connectors.
● Set your TV to VIDEO mode (or an input mode such as EXT1).
To |
| Back of unit |
[ANTENNA | To [VIDEO/ | To |
OUT] | ||
To | AUDIO | OUTPUT] |
OUTPUT] |
| |
[COMPONENT |
| |
|
| |
VIDEO OUT (Y/ |
|
|
PB/PR)] |
|
|
Component | Video/Audio |
|
video cable | cable (supplied) | |
(not supplied) |
| |
| (not supplied) | |
|
|
8
To connect to TV’s
APerform steps A – C of “Simple Connections”.
BConnect the unit’s
CConnect the unit’s [AUDIO OUTPUT] connectors to the TV’s AUDIO input connectors.
●You can obtain a
●If your TV is not
RF cable (supplied)
TV
To 75 ohm terminal
It’s essential that your unit be properly connected.
ATTENTION:
Connect the AC plug only after all connections to the TV has been completed.
8Component Video Connection
To connect to TV’s component video input connectors ^
APerform steps A – C of “Simple Connections”.
BConnect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)] connectors to the TV’s component video input connectors.
CConnect the unit’s [AUDIO OUTPUT] connectors to the TV’s AUDIO input connectors.
●You can obtain
●If your TV is not
●By using the component video connection, you can view the images in the progressive mode. For switching to the progressive mode, refer to “Scan Mode Set” (A pg. 60).
4Plug the end of the AC power cord into an AC outlet. This unit performs Plug & Play Set automatically.
●ALOADINGB blinks on the front display panel when the AC plug of the power cord is connected into an AC outlet. And it takes approximately 30 seconds for the unit to be turned on. This is not a malfunction.
NOTE:
It is necessary to connect any of above audio/video connections in addition to antenna connection with RF cable in order to view DVD playback on the TV.
