JVC DR-M100S manual To Make The Disc For On-Disc Timer Programming, DVD a Prog

DISC TIMER PRGM

PROG

OK SELECT WITH [CURSORS] SELECT THEN PRESS [ENTER]

EXIT

DISC TIMER PRGM

TIMER RECORDING EN 39

On-Disc Timer Programming

On-Disc Timer Programming is a function used with discs that are especially intended for a specific program. The disc is then programmed for a program you always watch every day or every week. Since older programs are automatically overwritten, a single disc can be used without worrying about how much recording capacity remains. You can program each disc to timer record as many as 8 programs up to 30 days in advance.

●Make sure that the unit’s built-in clock is set properly.

●Turn on the TV and select an input mode such as EXT1.

●Load a DVD-RAM or DVD-RW (VR mode) disc for programming.

ATTENTION:

●On-Disc Timer Programming is possible only with the disc for On-Disc Timer Programming.

●If data is recorded on a disc for On-Disc Timer Programming using a unit from another manufacturer, On-Disc Timer Programming may not function properly.

DVD A

PROG

Selection Keys (FGDE)

ENTER

To Make The Disc For On-Disc Timer Programming

1 Press PROG to access	PROGRAM CHECK
the Program Check
	DATE	START	STOP	CH	DAILY/WEEKLY	REC MODE
screen.	++++++++++++++++++ NEW TIMER PROGRAM ++++++++++++++++++

2Press selection keys to select ADISC TIMER PRGMB, then press

ENTER.

● When some programs are recorded on the disc,

a caution message

appears. To backup the recorded programs, press ENTER, and perform dubbing to other devices.

●When On-Disc Timer Programming has already been made on the disc, press selection keys to select ANEW TIMER PROGRAMB, then press ENTER.

3 Press selection keys to

set the desired date

(ADATEB), then press E.

4 Press selection keys to	DATE	START		STOP	CH
	10/07/03 THU	- - : - -	- -	- - : - - - -	- -
set the desired start time
(ASTARTB), then press E.	DAILY/WEEKLY	REC MODE			NAME
● Each press of FG	WEEKLY	SP
increases/decreases the
start time in 1-minute	EXIT	CONFIRM	SET TIMER PROGRAMING WITH [CURSORS]
		SELECT	THEN PRESS [ENTER]
interval.	PROG

●To increase/decrease the start time in 30-minutes interval, press and hold FG.

5Press selection keys to set the desired stop time (ASTOPB), then press E.

●Each press of FG increases/decreases the stop time in 1- minute interval.

●To increase/decrease the stop time in 30-minutes interval, press and hold FG.

6Press selection keys to set the desired channel (ACHB), then press E.

7Press selection keys to set ADAILY/WEEKLYB, then press E.

●For details on ADAILY/WEEKLYB setting, refer to “Daily/Weekly Recording Function” (A pg. 37).

8 Set the other recording
	DISC TIMER PRGM
options as required.
● “Recording Mode”
(A pg. 34)	DATE	START		STOP	CH
	10/07/03 THU	- - : - -	- -	- - : - - - -	- -
● “Modify Title Name”
(A pg. 46)	DAILY/WEEKLY	REC MODE
9 Press ENTER to access					NAME
	WEEKLY	SP
the Program
Confirmation screen.	EXIT	CONFIRM	SET TIMER PROGRAMING WITH [CURSORS]
			THEN PRESS [ENTER]
10 Press ENTER to	PROG	SELECT

complete the timer programming.

●To program another timer using “To Make The Disc For On- Disc Timer Programming”, repeat steps 1 - 10.

11 Press DVD A to turn off the power.

● is displayed on the front display panel.

●To disengage the timer mode, press DVD A again.

Cable Box or DBS Receiver Users

To timer record a satellite broadcast using On-Disc Timer Programming:

APerform On-Disc Timer Programming.

●Set the channel to the external input (AL-1Bor AF-1B) connected to the cable box or DBS receiver.

BSet the cable box or DBS receiver to the appropriate channel for recording.

●Leave the cable box or DBS receiver’s power on.