JVC GR-DVL9200 specifications EN Troubleshooting, Cont

52ENTROUBLESHOOTING

(cont.)

SYMPTOM	POSSIBLE CAUSES		CORRECTIVE ACTION
10. The colour of Snapshot looks	10. • The light source or the subject		10. • Set “FLASH” to “ON” in the
strange.	does not include white. Or		Menu Screen. Or find a white
	there are various different light		subject and compose your
	sources behind the subject.		shot so that it also appears in
			the frame (☞ pg. 16, 22).
11. Although Snapshot is	11. • The subject is too bright with		11. • Set “FLASH” to “ON” in the
attempted, flash does not	the flash set to “AUTO” or		Menu Screen (☞ pg. 22).
take place.	“AUTO	”.	• It can take up to 10 seconds
	• If blinks, the flash is being		to charge the flash.
	charged.		• Disengage Multi-Analyser 4
	• Multi-Analyser 4 or Multi-		or Multi-Analyser 9
	Analyser 9 is selected.		(☞ pg. 17).
	• The camcorder is in the		• Set the camcorder in the
	Record mode.		Record-Standby mode
	• In the Menu Screen, “GAIN		(☞ pg. 22).
	UP” is set to “OFF” or “P.AE/		• Set “GAIN UP” to “AUTO
	EFFECT” is set to “TWILIGHT”.		” or “AGC” (☞ pg. 19) or
	• The flash is pushed down.		disengage the “TWILIGHT”
			mode (☞ pg. 25).
			• Raise the flash using the
			FLASH OPEN Switch
			(☞ pg. 22).
12. Although a Snapshot is taken	12. • The subject does not look		12. • The subject should look
with the flash, Red-Eye	straight toward the flash.		straight toward the flash,
Reduction does not take	• The subject does not look at		especially the first flash. If the
place.	the first flash, which is an		subject does not see the first
	important part of Red-Eye		flash, it will be difficult for
	Reduction.		Red-Eye Reduction to take
	• The camcorder is too far from		place (☞ pg. 22).
	the subject.		• The flash is effective for
	• “FLASH” is not set to “AUTO		subjects at a distance of
	” in the Menu Screen.		approx. 0.7 m to 2 m from
			the camcorder (☞ pg. 22).
			• Set “FLASH” to “AUTO	”
			in the Menu Screen to display
			the Red-Eye Reduction
			indicator (☞ pg. 22).
13. The image taken using	13. • The flash is pushed down.		13. • Raise the flash using the
Snapshot is too dark.	• The flash emission window is		FLASH OPEN Switch
	covered by fingers, etc..		(☞ pg. 22).
	• The flash brightness is set to		• Do not cover the flash
	produce a darker image		emission window.
	(adjustment value: –3).		• Adjust the flash brightness to
	• The camcorder is too far from		a larger value (☞ pg. 23).
	the subject.		• The flash is effective for
	• Shooting was performed under		subjects at a distance of
	backlit conditions.		approx. 0.7 m to 2 m
			(☞ pg. 22).
			• Press the BACKLIGHT Button
			(☞ pg. 29).
14. The image taken using	14. • “FLASH” is set to “ON” in the		14. • Set “FLASH” to any
Snapshot is too bright.	Menu Screen.		parameter other than “ON” in
			the Menu Screen (☞ pg. 22).
			• Push down the flash.