PREPARATIONS FOR OPERATION
Turning the Power ON
PREPARATIONS FOR OPERATION
Loading/Unloading the Cassette
DISPLAY |
|
| ON | OFF |
|
| |
MONITOR SELECT | VTR | FULL AUTO |
|
| |||
|
|
|
|
| |||
| VTR indicator |
|
| ||||
| VF BRIGHT |
|
|
|
|
|
|
USER 1 USER 2 | USER 3 |
|
|
|
|
|
|
SHUTTER |
|
|
|
|
|
|
|
ND FILTER |
|
|
|
|
|
|
|
2 |
|
|
| LCD BRIGHT |
| CAM/VTR | |
1 |
|
|
| - | + |
|
|
MENU |
|
|
|
|
|
|
|
OFF |
|
|
| AUDIO SELECT |
| TC | |
|
|
|
|
|
| TCProHD | |
|
|
|
| DISPLAY | GENE. | ||
STATUS |
|
|
|
|
| UB |
|
POWER switch
POWERREC
CAM/VTR button
Turning the Power ON
1.Set the POWER switch to ON. The unit turns on in Camera mode.
The operation differs according to whether the unit is in the Camera mode or in the VTR mode.
The mode switches each time you press the CAM/VTR button.
When the mode is switched, the VTR indicator displays the following statuses.
While the mode is being switched : Flashing
In VTR mode | : Lit |
In Camera mode | : Off |
Camera mode
The
*Playback is also possible in the Camera mode. Playback operation becomes possible when the STOP button is pressed to set the VTR operation mode indica-
tor to indicate “STOP”.
VTR mode
The
“STOP” is displayed in the VTR operation mode indication area of the LCD monitor or in the viewfinder.
HDV/DV input is possible through the IEEE1394 connector.
Turning the Power OFF
1.Place the
2.Set the POWER switch to OFF.
3.Remove the battery pack or the power supply to the DC IN connector. (When the camera is not going to be used for a longer period.)
CAUTION
•Do not set the POWER switch to OFF while recording is taking place.
Confirm that the “STBY” or “STOP” indication is shown in the VTR operation mode indication area before the power is turned off.
Should the POWER switch accidentally be set to OFF during a recording, wait at least 5 seconds before turning the power on again.
•Always set the POWER switch to OFF before disconnect- ing the power supply.
Do not turn the battery pack or AC power supply OFF while the POWER switch on the camera is still set to ON.
REC/SAVE | Tape window | |
switch | ||
|
EJECT switch
Cassette holder
Cassette cover
Cassette Loading
Use a videocassette tape marked MiniDV.
•To record, slide the switch on the back for use in preventing accidental erasure to the “REC” side.
•Remove any the tape slack before loading.
1.Turn the POWER switch ON.
2.Slide the EJECT switch on the top panel of the camcorder to the side.
The videocassette cover opens automatically and a video- cassette tape can be inserted.
3.Insert a videocassette tape into the videocassette holder. With the tape window facing out, move the switch on the back of the videocassette up and firmly push the center back of the videocassette straight in as far as it will go.
4.Carefully push the center of the videocassette cover in the direction of the arrow as far as it will go to close it.
• After the cover is closed, it takes about 10 seconds until
recording can begin or the camcorder can enter stop mode.
If the power is on, the modes are as shown below.
MODE | REC/SAVE switch | |
| REC | SAVE |
Camera | STOP mode | |
|
| REC INHIBIT is displayed |
|
| on the LCD monitor and in |
|
| the viewfinder. |
VTR | STOP mode |
|
Unloading the Cassette
1. Turn the POWER switch to ON.
2.When the camcorder is in shooting standby mode or stop mode, slide the EJECT switch to the side and wait until the videocassette cover opens completely.
•The LED next to the EJECT switch flashes.
A few seconds pass before the videocassette tape is ejected.
3.The LED turns off and the videocassette cover opens.
•Take out the videocassette tape.
4.Carefully push the center of the videocassette cover in the direction of the arrow as far as it will go to close it.
CAUTION
•When you close the videocassette cover, push it in firmly as far as it will go. If the videocassette cover is not closed properly, it becomes
If this happens, firmly push the videocassette cover in again as far as it will go to lock it.
•Do not slide the EJECT switch while recording is in progress.
If you slide the EJECT switch while recording is in progress, the tape is ejected.
•Do not leave the videocassette cover open for a long time.
Dust or dirt may enter the inside and cause damage.
•Do not touch the videocassette cover or interfere with the eject operation while ejecting is in progress. This will cause damage.
34 | 35 |
