Level Change via Bar Code

Enables level changes based upon detection of a bar code. The default value is Undefined.

Microimager 70

Microimager 70/AFM

Scanner 900

Scanner 923

Scanner/Microimager 990

Scanner 9500

1.Select Level Change via Bar Code.

 

Mode Number: 10

Mode Name: MODE10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mode Configuration

 

 

 

 

 

 

 

 

Bar Code Reader

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MODE 10

Mode Name

Ftswitch Pressed

Undef

 

 

 

Bar Code Reading Status

 

 

 

 

 

Bar Code Type

 

 

3 Lvl

Index Format

Ftswitch Released

Undef

 

 

 

 

 

 

 

 

# of Bar Code Characters

 

 

Supprs

IA Display Format

Ftswitch Cnf Tone

Off

 

 

 

 

 

 

 

 

Bar Codes per Document

 

 

4233

IA Field Widths

Patch Reader 1

Off

 

 

 

 

 

 

 

 

Distance Between Codes

 

 

2112

Level Rules

Patch Reader 2

Off

 

 

 

 

 

 

 

 

Scan Direction

 

 

None

Batching

Patch Definition

Lvl 2

 

 

 

 

 

 

 

 

Image Processing

 

 

Auto

AEC Mode

Bar Code

Off

 

 

 

 

 

 

 

 

Partial Read Enabled

 

 

Duplex

Film Mode

Confirmation Tone

N N N

 

 

 

 

 

 

 

 

Min. Partial Characters

 

 

?????

Reduction Ratio

OCR Status

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Roll

# of Cassettes

COIN User Channel

On

 

 

 

DSA Patch Reading Status

 

 

Comic

Film Writer

Printer Control

Disply

 

 

 

Patch Horizontal Location

 

 

Off

Image Mgmt Code

Primary DP-1

Off

 

 

 

End Fed Patch Read Status

 

 

Off

Length Monitor

Secondary DP-1

Off

 

 

 

Level Change via Bar Code

 

 

Off

Skew Monitor

Doc. Printer 12

Off

 

 

 

Previous Menu

 

 

Xport

Check Stacker

Document Sorter

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Patch Level

 

 

 

 

 

 

 

 

 

Off

Endorser

Mode Overrides

No Sav

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Not Used

Film Definition

F

 

 

 

Level 0

 

 

 

 

 

 

Level 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Level 2

 

 

 

 

 

 

 

 

 

 

 

Save & End Session

Don't Save & End Session

 

 

 

Level 3

 

 

 

Previous Menu

End Configuration

 

 

 

 

Undefined

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Previous Menu

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Select the desired level to be assigned when a bar code is detected.

NOTE: It is recommended that patch codes, rather than bar codes, be used to perform document level changes. Using patch codes to alter document image levels is much more reliable and accurate than the use of bar codes to alter document image levels. The lower reliability level which may be experienced using bar codes to alter document image levels may have serious ramifications, depending upon the application. It is suggested that you contact Marketing Support in Rochester if you wish to implement this feature.

A-61097 May 1997

3-73

Page 123
Image 123
Kodak A-61097 manual Select Level Change via Bar Code