Compliance and Warranty Information | Lantronix Hub specification

MSS VIA Connectors_______________________________________________7-18

PC Card Slot __________________________________________________7-18

Serial Connectors ______________________________________________7-18

MSS4 Connectors _________________________________________________7-18

Serial Connectors ______________________________________________7-18

MSS100 Connectors _______________________________________________7-18

DB25 Connector _______________________________________________7-18

Modem Wiring_________________________________________________7-18

8:Updating Software __________________________________________ 8-18

Obtaining Software ________________________________________________8-18 Via the Web __________________________________________________8-18 Via FTP ______________________________________________________8-18 Reloading Software ________________________________________________8-18 Reloading Sequence____________________________________________8-18 Troubleshooting Flash ROM Updates __________________________________8-18

A:Compliance and Warranty Information _________________________ 8-18

Compliance Information_____________________________________________8-18 Warranty ________________________________________________________8-18

vi

Image 7

Lantronix Hub manual Compliance and Warranty Information

Contents

MSS User Guide Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer & Revisions Contents Configuration Using the MSS Compliance and Warranty Information Introduction to the MSS Family MSS Family Features Protocols About The Documentation Terms MSS User Guide Introduction to the MSS Family MSS-VIA Installation InstallationComponents MSS-VIA LEDs MSS-VIA Rear Panel Example Wired Network Layout Installation Procedure MSS User Guide Installation Pinging the MSS Humidity MSS-VIA SpecificationsPower power cube adaptor Temperature MSS4 Components MSS4 Installation MSS Connected to a Serial Device and Network MSS4 LEDs MSS User Guide Installation MSS4 Specifications 10 MSS100 Front Panel MSS100 Installation 12 MSS Network Layout MSS100 LEDs 13 MSS Connected to Serial Device and Ethernet 14 Pinging the MSS MSS100 Specifications Privileged User Status Getting Started From the Action menu, select Assign IP Address IP Address ConfigurationUsing EZWebCon Using a Web Browser Entering ARP and Ping Unix Using ARP and Ping Using the Serial Console Using a DHCP, BOOTP, or Rarp Reply Web Browser Login and Configuration Incoming LoginsLogin Password Incoming TCP/IP Logins Telnet Serial Port LoginsEZWebCon Login and Configuration Rlogin Remote Console Logins Changing the Login PasswordIncoming LAT Logins Logout Outbound Connections Overview ConfigurationRebooting the MSS Normal Reboot Factory Defaults Protocol ConfigurationTCP/IP Configuration Name Server Specifying a Gateway for MSS-VIA and MSS4 Supported Mibs IP Security Routing and Encapsulation IPX NetWare ConfigurationConfiguring Snmp Snmp Trap Support Loadhost Internal Network Number Server Identification LAT ConfigurationService Groups Circuit Timer Two-Wire Mode RS-485 Configuration 22 Enabling Two-Wire RS-485 Mode for MSS4 Four-Wire Mode Termination TXDrive Access Mode Serial Port ConfigurationAutostart Serial Data 36 Configuring an Autostart Character for MSS-VIA and MSS4 Character Size, Parity, and Stop Bits Baud Rate Flow Control Modems and Modem Signaling Modem Control Signal CheckingDSRLogout DTRWait Logouts Preferred Host ConfigurationDedicated Host Region Enabling 802.11 Networking MAC Address Extended Service Set ID Essid Setting the WEP Key and Index Number Network ModeChannel Modem Cards Formatting an ATA Flash CardEncrypted Traffic Outgoing Calls Incoming Calls Incoming Connections Using the MSSSocket Connections Outbound Connections Interactive ConnectionsTCP/IP Socket Connections Backward, Forward, and Switches Break Key and Local SwitchSession Control Show Status DisplaysDisconnect and Resume Session Limits Serial Tunnel UDP Configuration TCP Configuration Enabling Multihost Mode Multihost Mode Adding Hosts Modem Emulation ModeRemoving Hosts 17. Enabling Modem Mode for MSS100 Modem Mode Commands Wiring Requirements Sequential Hostlist ModeCOM Port Redirector Power-up Troubleshooting TroubleshootingPower-up Problems and Error Messages Bootp Troubleshooting Dhcp TroubleshootingBootp Troubleshooting Dhcp Troubleshooting Rarp Troubleshooting Rarp TroubleshootingTftp Troubleshooting Modem Configuration Checklist Change Bootp Enabled, Disabled Entering Commands at the Boot PromptInit Change Loadhost ipaddress Change Dhcp Enabled, DisabledChange Hardware Change Ipaddress ipaddress Technical Support Europe, Middle East, and Africa Technical Support Pinouts Ethernet ConnectorMSS VIA Connectors Serial Connectors RS-232 DB9 Connector MSS4 ConnectorsRS-485 DB9 Connectors DB25 Connector MSS100 ConnectorsRS-232 DB9 Connectors DSR Data Signal Ready versus CD Carrier Detect Modem WiringDTR Data Terminal Ready Via the Web Via FTP Updating SoftwareObtaining Software Reloading Software FTP Flash ROM Troubleshooting Troubleshooting Flash ROM UpdatesNetWare MSS User Guide Updating Software Compliance Information Compliance and Warranty Information Warranty