Manuals / Linksys / Computer Equipment / Computer Drive

Linksys EFG120 manual The Front Panel

Models: EFG120

1 61

Download 61 pages 37.01 Kb

Page 12

The Front Panel

EtherFast Network Attached Storage (120GB with PrintServer)

The Front Panel

The Network Attached Storage’s LEDs, which indicate status information about network activity, and power button are located on the front panel.

Ready/Status	Green or Orange. This LED is solidly lit green when the Network Attached Storage is working
	properly. It flashes during start-up, shutdown, any self-test, or a firmware upgrade. If the LED
	is orange, there is an error.
LAN	Green or Orange. The LAN LED serves two purposes. If the LED is continuously lit, the Network
	Attached Storage is successfully connected to a device through the LAN port. If the LED
	flashes, it indicates network activity. If the LED is orange, there is a data collision.
Disk	Green. The Disk LED flashes when the Network Attached Storage is reading or writing data.
Disk Full	Green. The Disk Full LED lights up when the Network Attached Storage has reached its
	maximum storage capacity. It flashes when it reaches 98% of total capacity.
BackUp	Green. The BackUp LED flashes when the Network Attached Storage’s backup utility is active.
Disk 2	Green. The Disk 2 LED flashes when Disk 2 is reading or writing data.
Disk 1	Green. The Disk 1 LED flashes when Disk 1 is reading or writing data.
Power Button	If the Network Attached Storage is powered off, you can start it up by briefly pressing the
	power button. To power down the Network Attached Storage, press the power button, and its
	internal shutdown process will begin. The Network Attached Storage must be powered off this
	way, or through the Administration - Status tab of the Web-based Utility (refer to “Chapter 5:
	Configuring the Network Attached Storage”).

Chapter 2: Getting to Know the Network Attached Storage

Figure 2-2: Front Panel

5

The Front Panel

Image 12

Linksys EFG120 manual The Front Panel

Contents

WIRED Network Attached StorageUser Guide 120GB with PrintServerHow to Use this Guide Copyright and Trademarksword definition Table of Contents Chapter 3 Connecting the Network Attached StorageChapter 4 Setting Up the Network Attached Storage Chapter 5 Configuring the Network Attached StorageAppendix B Installing a Second Hard Drive Appendix C Setting Up the Built-in PrintServerAppendix F Specifications Appendix G Warranty InformationList of Figures Figure 4-25 Copy Files Screen Figure B-4 Insert Screw through Left Side of Tray Chapter 1 Introduction WelcomeWhat’s in this User Guide? Appendix H Regulatory Information Appendix I Contact InformationEtherFast Network Attached Storage 120GB with PrintServer Chapter 1 IntroductionChapter 2 Getting to Know the Network Attached Storage The Back PanelThe Front Panel The Beeper Codes Chapter 3 Connecting the Network Attached Storage Chapter 4 Setting Up the Network Attached Storage Setup WizardOverview Figure 4-3 IP Settings Screen Figure 4-4 Fixed IP Address Screen Figure 4-5 DHCP Server Settings Screen Figure 4-7 Review Settings Screen Installation of BrightStor ARCserve Backup for Windows Figure 4-13 License Agreement Screen Figure 4-15 License Key Entry Screen Figure 4-17 Select Products Screen Figure 4-18 Select Database Screen Figure 4-19 Set Password Screen Chapter 4 Setting Up the Network Attached StorageInstallation of BrightStor ARCserve Backup for Windows Figure 4-20 System Account ScreenFigure 4-21 Product List Screen Figure 4-22 Copy Files Screen Figure 4-23 Licensing Information Screen 17. On the Install Summary screen, click the Finish button Figure 4-26 Install Summary ScreenChapter 4 Setting Up the Network Attached Storage Installation of BrightStor ARCserve Backup for Windows19. Click the OK button Chapter 4 Setting Up the Network Attached Storage Installation of BrightStor ARCserve Backup for Windows22. Read the information, and click the Continue button Figure 4-31 Information ScreenChapter 5 Configuring the Network Attached Storage GigaDrive StatusThe Home Tab - User Log in Private Data The Home Tab - Disk 1 Public Data or Disk 2 Public DataThe User Password Tab The Administration Tab - LANLAN Settings DHCP Server DNS ServerThe Administration Tab - System System InformationOptions The Administration Tab - Users Users InformationThe Administration Tab - Status User MembershipSystem Printer DiskE-Mail Alerts The Administration Tab - Advanced - Groups Group InformationThe Administration Tab - Advanced - Shares Shares InformationThe Administration Tab - Advanced - Backup Backup SettingsThe Administration Tab - Advanced - Disk Disk SettingsDefrag StandbyThe Administration Tab - Advanced - Upgrade The Administration Tab - Advanced - SetupUpgrade Settings The User Guide TabAppendix A Troubleshooting Appendix A TroubleshootingThis can happen in the following situations Appendix B Installing a Second Hard Drive Figure B-3 Make Sure Connections are Tight 9. Slide the drive into the second drive bay 14. Click the Administration tab and then the Advanced tab Appendix C Setting Up the Built-in PrintServer Appendix C Setting Up the Built-in PrintServer 7. Double-click the Add Printer icon to begin the Add Printer WizardPrinter Icon Figure C-4 Welcome to the Add Printer Wizard ScreenFigure C-5 Local or Network Printer Screen Figure C-8 Select Your Printer Congratulations! You have added a printer to your network Appendix D Windows Help TCP/IPShared Resources Network Neighborhood/My Network PlacesAppendix E Glossary Subnet Mask - An address code that determines the size of the network Appendix F Specifications Appendix G Warranty Information Appendix H Regulatory Information Appendix I Contact Information