Section 6

Electrical System

 

 

4. FREEZE

The water pump starts after the pre- chill. An even flow of water is directed across the evaporator and into each cube cell, where it freezes.

The water fill valve will cycle off then on one more time to refill the water trough.

When sufficient ice has formed, the water flow (not the ice) contacts the ice thickness probes. After approximately 10 seconds of continual contact, a harvest cycle is initiated.

NOTE: The ice machine cannot initiate a harvest cycle until a 6- minute freeze lock has expired.

L1

 

 

 

L2 or N

Ground

 

 

Water Valve

(99)

 

 

 

 

 

(20)

(21)

(89)

(55)

 

(61)

(22)

 

High

 

 

Control Board

 

Harvest Valve

 

Pressure

 

 

(2)

 

 

(88) Cutout

(60)

(77)

 

(6)

 

 

(80)

 

 

(5)

 

Dump Valve

(75)

 

(1)

 

(76)

 

(7)

 

(81)

 

 

(4)

(57)

Water Pump

 

 

 

(98)

 

 

 

 

 

(42)

Trans.

(58)

 

 

 

Fuse (7a)

Terminates at

 

 

 

 

 

 

 

Pin Connection

 

 

 

 

 

 

 

(59)

 

 

 

L2

 

 

Contactor Coil

 

 

 

(25)

 

 

(56)

 

 

 

 

(26)

 

Air Compressor

 

 

 

 

 

 

Ice Thickness

 

(9)

 

 

 

(74)

Probe

 

(8)

 

 

Water Level Probe

 

 

 

 

Bin Switch

 

Low DC

 

(6)

 

 

 

 

 

 

 

Voltage

 

 

 

Clean

 

 

Plug

 

(1)

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

(2)

 

ICE

 

 

(Red)

 

 

 

 

 

 

 

 

 

 

 

Compressor

 

 

Run Capacitor

Contactor

Overload

(Yellow)

 

(46)

 

 

 

 

 

 

(50)

Contacts

 

 

 

 

 

(Black)

 

 

 

 

 

(45)

L1

 

 

 

 

 

(51)

(85)

(86)

 

 

PTCR

 

Fan Motor

 

Fan Cycle

 

 

 

 

 

 

 

Control

 

 

 

 

Run Capacitor

SV3137-5

 

Self-Contained — Freeze

Table 6-4. Self-Contained Models

4.Freeze (Until 10 Seconds of Water Contact with Ice Thickness Probe)

Toggle Switch

Bin Switch

Control Board Relays

ICE

Closed

#1

Water Pump

ON

#2

Harvest Valve (Left)

OFF

#3

Harvest Valve (Right)

OFF (When Used)

#4

Air Compressor

OFF (When Used)

#5

Water Inlet Valve

Cycles OFF, then ON

one more time

 

 

#6

Water Dump Valve

OFF

#7

Contactor Coil

Closed / ON

#7A

Compressor

ON

#7B

Condenser Fan Motor

May Cycle ON / OFF

Safety Controls (Which could stop ice machine operation)

 

 

High Pressure Cut-Out

Closed

 

Main Fuse (On Control Board)

Closed

Part Number 80-1634-3

6-5

Page 43
Image 43
Manitowoc Ice S1800 Self-Contained Freeze Self-Contained Models, Toggle Switch Bin Switch Control Board Relays