FUNCTIONS | NAMES AND |
CONNECTIONS | BASIC |
OPERATION | BASIC |
ENGLISH
ADVANCED OPERATION
SR5004 REMOTE CONTROLLER
BASIC OPERATION
NORMAL MODE
(When operating Marantz AV equipment products)
This remote controller is preset with a total of 12 types of remote codes, including Marantz BD, DVD, VCR (VCR deck), DSS (Satellite broadcasting tuner), TV (Television), CD, CDR, AUX, TUNER, USB,
Learning is not necessary for Marantz products. You can use these products without setting any codes.
1. Press the SOURCE button. For this example, press DVD.
Pressing the SOURCE button once changes
See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.
Remote | Corresponding |
| |
controller | Device name | ||
source name | preset code |
| |
TV | TV | Television | |
DVD | DVD | DVD player | |
CD | CD | CD player | |
DSS | SATELLITE | Satellite | |
broadcasting | |||
|
| tuner equipment | |
BD | BD | ||
player | |||
|
|
Importants
• Some codes may be not match your equipment.
SCANNING THE CODE TABLE
2.
3.
2.
3.
5.
1. Switch on the appliance which should be controlled.
2. Press the INFO button.
The SEND indicator will blink twice.
3. To view the code for first digit, press 1 once.
Count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number.
4. Then press 2 to check the second digit of the code. Now press 3 and 4 to check the third and fourth digits of the code.
Note
If a code digit is “0”, the SEND indicator will not blink.
RESETTING THE CODE
CONNECTIONS | ADVANCED |
SETUP | |
OPERATION | ADVANCED |
TROUBLESHOOTING | |
OTHERS |
the remote control to the settings for the source that was pressed.
To change the amplifier on other source, press the SOURCE button twice (double- click). The code is sent, and then the amplifier source changes to DVD.
SETTING THE BACK LIGHT
Pressing the Light button located on the side of the remote controller lights the remote controller’s backlight. Pressing the button again while the backlight is lit lights the backlight for another 2 seconds.
To turn off back light, press and hold down the SET and OFF button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ON button until SEND indicator blinks twice.
Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment products)
This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, CD, DVD and DSS. Settings can be made in one of two ways.
When the preset codes are set, the following codes are contained in the source button of the remote controller.
| In this case, you can use LEARN mode to store | 2. Press and hold down the SOURCE button |
|
| 1. | ||
| these codes. |
|
| ||||
| for appliance which should be controlled |
|
| ||||
• The preset codes do not cover full functions. |
|
|
| ||||
and press SET button until the SEND |
|
|
| ||||
| If you need extra function, use LEARN mode to |
|
|
| |||
| indicator blinking twice. Then back light |
|
| 1. | |||
| store extra function. |
|
| ||||
| flushes. |
|
|
| |||
• Wen the batteries are getting weak, the preset |
|
|
|
| |||
3. Aim the remote control at the appliance |
|
|
| ||||
| procedure is not successful. |
|
|
| |||
|
| and slowly alternate between pressing |
|
|
| ||
PROGRAMMING WITH THE | INPUT 3 button and the SOURCE ON/OFF |
|
| 2. | |||
button for the appliance. |
|
| |||||
|
| 4. Stop when the appliance turns off. |
|
|
| ||
| 1. | 5. Press ENTER button once to lock in the | 1. |
|
| ||
| 2. | code. |
| Press and hold down the SOURCE button | |||
| 1. |
|
|
| for appliance which should be controlled | ||
| CHECKING THE CODE |
| and press SET button until the SEND | ||||
|
| indicator blinking twice. | |||||
|
|
|
|
| |||
|
|
| 2. | 2. | Then back light flushes. | ||
1. |
|
| Press the below codes to reset. | ||||
Press and hold down the SOURCE button for |
|
| |||||
1. |
|
| TV | : 1000 | |||
| the appliance which should be controlled and |
|
| ||||
|
|
|
| DVD : 2000 | |||
| press SET button until the SEND indicator |
|
|
| |||
|
| 3. |
| CD | : 3000 | ||
| blinks twice. Then back light flushes. |
|
| ||||
2. | 1. |
| DSS : 4000 | ||||
|
|
| |||||
Press the | 4. |
| BD | : 5000 | |||
| for appliance (code table at the end of this |
|
| The indicator will blink twice. | |||
|
|
|
| ||||
| book) |
|
|
|
|
| |
| When the procedure is successful, the | 1. Press and hold down the SOURCE button | Note |
| |||
| SEND indicator will blink twice. | After this procedure, the selected SOURCE button | |||||
|
| for appliance which should be controlled | |||||
|
| is set initial code. | |||||
Note | and press SET | button until the SEND | |||||
|
|
|
If the indicator did not blink twice, then repeat steps | indicator blinking twice then back light | |
flushes. | ||
1 through 2 and try entering the same code again. | ||
|
76