Marantz SR5004 manual Tuner, USB SR6004 only

Symptom	Cause	Solution	Page
No sound is heard		No sound is heard from the
from the monitor	HDMI audio enable mode is
		monitor TV in Enable mode. Select	36
TV connected to	established.
		Through.
the HDMI terminal.
Image and audio		Use a short cable.
are unstable		Use of a cable no longer than 5	–
over an HDMI	The connection uses a long cable.	meters is recommended.
connection.
(There is noise,		Use a Category 2 (high-speed	–
the stream is		supported) cable.
interrupted, etc.)

TUNER

Symptom	Cause	Solution	Page
		Make sure the AM and FM
Cannot receive	The antennas have not been	antennas are properly connected to	15
AM or FM signals.	connected properly.	the AM and FM antenna terminals,
		respectively.
A noise is	The unit is receiving interference	Change the location of the AM
generated when			–
receiving an AM	from other components.	antenna.
signal.
A noise is	The signal from the broadcasting
generated when		Install an outdoor FM antenna.	15
receiving an FM	station is weak.
signal.

USB (SR6004 ONLY)

Symptom		Cause		Solution	Page
Even when the			• Check whether the USB storage		–
				device and USB cable are firmly
USB storage
				plugged into the unit's USB
device is
	•	The unit cannot recognize the		connector.
connected, “NO					–
		USB storage device because of	•	Try removing the USB storage
DEVICE” remains
		connection trouble or some other		device from the unit, and re-
on the status
		issue.		connecting it.
display, and the
			•	Try turning the unit’s power off	–
device is not
				and back on, and re-connecting
recognized.
				the device.
	•	A device that cannot be	•	Even when a USB storage device	–
“CHECK DEVICE”		recognized by the unit has been		complies with the USB Mass
		connected.		Storage Class standard, it may
appears on the
				not be possible to play its files
status display
				using the unit. (This does not
when the USB
				mean that something is wrong
storage device is
				with the unit itself.)
connected.					–
	•	The device has been connected	•	USB storage devices cannot be
		through a USB hub.		connected through a USB hub.

					ENGLISH
				TROUBLESHOOTING
Symptom		Cause		Solution		Page
“CHECK FS”	•	A format other than FAT16	•	Set the format to FAT16 or		–
		or FAT32 is used as the USB		FAT32, and record the files.
appears on the
		storage device’s format.
status display						–
	•	A USB storage device that has	•	Use a USB storage device that
when a USB
		been formatted using a file		has been formatted using a file
storage device is
		system not supported by the unit		system supported by the unit.
connected.
		is being used.
“!OVER			No guarantees are made for the
CURRENT!”			operation of a hard disk drive that
appears on the	The overcurrent protection function		is powered from the unit's USB			–
status display	of the unit’s USB connector has		connector.
when a USB	been triggered.		Remove the connected USB
storage device is			storage device, and turn the unit's
connected.			power off and back on.
“NO AUDIO FILE”
appears on the	No playable files have been		Record the supported file on a USB
status display when						64
a USB storage	recorded on a USB storage device.		storage device.
device is connected.
“CHECK FILE”	•	An attempt has been made to	•	The unit cannot play copyright-		–
appears on the		play a copyright-protected file.		protected files.		–
status display	•	The file is damaged.	•	Check the file.
when a USB		Alternatively, its extension and
storage device is		file structure are incompatible.
connected.
	•	The USB storage device is	• If the device is partitioned into			–
The files recorded		partitioned into a number of		a number of partitions, displays
		partitions.		only for the first partition will
on the USB
				appear.
storage device are
	•	The number of folders exceeds	•	No displays appear for folders		–
not displayed.		700 or the number of files		after folder no.700 or for files
		exceeds 65535.		after file no.65535.
“PRESS TOP KEY”			Press the TOP button, and try
appears on the status	The file cannot be read properly.					–
			rereading the file.
display.
“PRESS MODE	An iPod not supported by the unit's		Press the SETUP/MODE button,			8
KEY” appears on
	direct mode has been connected.		and use the iPod in remote mode.
the status display.
“CHECK iPod”			Turn off the unit's power and turn it
	The iPod could not be detected		back on. If the iPod still cannot be
appears on the			detected, reset the iPod. For details			16
	properly.
status display.			on how to reset the iPod, refer to
			the iPod's operating instructions.

NAMES AND	FUNCTIONS
BASIC	CONNECTIONS
BASIC	OPERATION
ADVANCED	CONNECTIONS
SETUP
ADVANCED	OPERATION
TROUBLESHOOTING
OTHERS

81