Marantz SR5004, SR6004 manual Video, Hdmi, Or component as the source, Not enabled when the unit is

FUNCTIONS	NAMES AND
CONNECTIONS	BASIC
OPERATION	BASIC
CONNECTIONS	ADVANCED
SETUP
OPERATION	ADVANCED
TROUBLESHOOTING
OTHERS

ENGLISH

TROUBLESHOOTING

VIDEO

Symptom		Cause		Solution	Page
	•	The monitor TV connection,	•	See the monitor TV's instruction	–
		input switching, etc., are not set		manual.
No image on the		up correctly.	• Make an HDMI connection to		14
	• The unit has an HDMI
monitor TV.
		connection to the source		the monitor TV.
		component, but no HDMI
		connection to the monitor TV.
The audio or	The input cables are incorrectly		Connect the cables properly,
the image does
			referring to the connection		12 - 14
not match the	connected.
			diagram.
selected source.
	•	The video recording component	•	Make sure the recording	–
		jack does not match the source		component jack matches the
Cannot record to a		component jack.		source component jack. (VIDEO
				or S-VIDEO)
VCR, etc.
	•	A copy-protected signal is being	•	Video signals that include copy-	–
		received.		protected signals cannot be
				recorded.
	When special playback is		Connect a monitor TV using
The converted	performed by the video deck, the
	conversion may not be carried out		the same format (video, s-video		13
video signals are
	normally, causing the video signals		or component) as the source
disturbed.
	to be disturbed and preventing the		component.
	images from being shown.

HDMI

Symptom	Cause	Solution	Page
	The HDMI cable is improperly	Check the HDMI cable connection.	14
	connected.
		Use of a cable no longer than 5
	The unit is connected with a non-	meters is recommended to ensure	–
	spec HDMI cable.	stable operation, prevent picture
		degradation, etc.
	The connection between	Turn the power on again to all
	components over an HDMI
		the components on the HDMI	–
	connection has not been
		connection.
	authenticated.
		Make sure the unit's HDMI	35
		settings are correct.
		Set the unit for HDMI input, as
		explained in the instruction manual	–
		of the video component (TV,
There is no picture		projector, etc.).
with the HDMI		Make settings to enable HDMI
connection.	The HDMI settings are incorrect.	output, as explained in the	–
		instruction manual of the source
		component (Blu-ray disc player, Set
		Top Box, etc.).
		Match the resolution for both
		components, as explained	35
		in the instruction manual of
		the component on the HDMI
		connection.
	The unit is connected to the video	Connect an HDCP-compatible	14
	component (TV, projector, etc.) by
		video component.
	DVI connector.
	The power to the unit is turned
	off. (HDMI connections are	Turn on the main power to the unit.	16
	not enabled when the unit is in
	STANDBY mode.)
It takes time for	The connection is being	Some HDMI components require
the image to be
	authenticated between components	time for authentication. There is	–
displayed over an
	on the HDMI connection.	nothing wrong with the unit.
HDMI connection.
		Make settings to enable HDMI
		audio output, as explained in the	–
		instruction manual of the source
		component (Blu-ray disc player, Set
	The HDMI settings are incorrect.	Top Box, etc.).
There is no audio		Set so that the HDMI audio output
		setting matches the signals
playback over an
		supported by the unit, as explained	–
HDMI connection.
		in the instruction manual of the
		source component (Blu-ray disc
		player, Set Top Box, etc.).
	HDMI audio through mode is	No sound can be delivered from
		the unit in this mode. Select the	36
	established.
		Enable setting.

80