Marantz SR6004 Example, Setup, English, Names And Functions, Basic, Connections, Operation, Notes

8. Repeat step 7 until measuring up to 6 points measuring the main listening position and other positions where people will

9. Checking Measurement Results

When calculations for the measurement results end, a screen appears for confirming

[Example]

Confirmation screen for the distance from speakers to the listening position

ENGLISH

SETUP

*Auto is displayed to indicate that the speaker size and crossover frequency results were automatically measured.

NAMES AND FUNCTIONS

commonly listen.

When all measurements end, the following GUI appears on the display.

Audyssey MultEQ Setup

Speaker Check : OK

Calculate

the calculation results.

Check Result

Speakers Configuration

Speakers Size

Speakers Distance

Channel Level

Crossover Frequency

Store

Speakers Distance

Unit

Front Left

Front Height Left

Center

Front Height Right

Front Right

Surround Right

Surround Back Right

Surround Back Left

Surround Left

Subwoofer

Return

: Up / Down :

:Meters

:30.0 ft

:30.0 ft

:19.3 ft

:29.6 ft

:29.6 ft

:21.5 ft

:12.3 ft

:11.6 ft

:16.3 ft

:12.5 ft

Enter : Return Exit : Exit

10. Storing Measurement Results in Memory Once finished confirming the measurement results, select “Return” with the 3/4 cursor buttons and press the ENTER button to display the Check Result screen.

Check Result

Speakers Configuration

Speakers Size

Speakers Distance

Channel Level

Crossover Frequency

Store

BASIC	CONNECTIONS
BASIC	OPERATION

: : Enter : OK Exit : Exit

Select “Calculate” with the 3/4 cursor buttons and press the ENTER button to calculate measurement results. During calculations, the following GUI appears on the display.

Audyssey MultEQ Setup

--------------

: Up / Down : Enter : Select Exit : Exit

Select items to check with the 3/4 cursor buttons and press the ENTER button to enter them.

Note

To check equalizer (MultEQ®) parameters, see page 38.

[Example]

Confirmation screen for speaker detection

*The units can be changed by moving the cursor to Meters of Unit and pressing 1 / 2 the cursor buttons. Each time a 1 / 2 cursor button is pressed, the units alternate between Feet and Meters.

Note

This system cannot measure a distance of 9.15 m (30.0 ft) or higher. In this case, >9.15 m (>30.0 ft) is displayed.

[Example]

Confirmation screen for channel level.

: Up / Down : Enter : OK Exit : Exit

Place the cursor on “Store” and press the ENTER button to store all parameters includingtheequalizerparametersinmemory. If not wanting to store the calculation results

ADVANCED CONNECTIONS

Now Calculating!

: : Enter : Exit :

Speakers Configuration

Check Speaker Results

Front Left

Front Height Left

Center

Front Height Right

Front Right

Surround Right

Surround Back

Surround Left

Subwoofer

Return

:Yes

:No

:No

:No

:Yes

:Yes

:No

:Yes

:Yes

Channel Level
Front Left	:	0.0dB
Front Height Left	:	0.0dB
Center	:	-6.5dB
Front Height Right	:	0.0dB
Front Right	:	-1.5dB
Surround Right	:	+1.0dB
Surround Back Right	:	+9.5dB
Surround Back Left	: +12.0dB
Surround Left	:	-2.5dB
Subwoofer	: -12.5dB
Return

in memory, press the Exit button.

Note

Pressing “Exit” prior to pressing “Store” erases all measurement results and calculation results, therefore operate the remote controller with care.

When storing operations end, the following GUI appears on the display.

Speaker Setup

SETUP

ADVANCED OPERATION

Notes

::

Enter : Return

Exit : Exit

: : Enter : Return Exit : Exit

Auto Setup

Manual Setup

•Fewer than 6 positions may be measured, but it is recommended to measure in all 6 positions for best results. Measuring in fewer than 3 position is not recommended as it does not provide enough acoustical information for good correction.

•The time needed to complete calculations depends on the number of connected speakers and measured listening positions. The more speakers and listening positions, the more time is needed.

[Example]

Confirmation screen for speaker size.

	Speakers Size
	Front Left	: Auto
	Front Height Left	: Auto
	Center	: Auto
	Front Height Right	: Auto
	Front Right	: Auto
	Surround Right	: Auto
	Surround Back Right	: Auto
	Surround Back Left	: Auto
	Surround Left	: Auto
	Return
:	:	Enter : Return Exit : Exit

[Example]

Confirmation screen for crossover frequency.

Crossover Frequency
Front	: Auto
Front Height	: Auto
Center	: Auto
Surround	: Auto
Surround Back	: Auto
Return

: : Enter : Return Exit : Exit

Return

: Up / Down : Enter : Select Exit : Exit

Note

•Do not turn the power to the unit off while storing parameters in memory. This may erase or corrupt data in the unitʼs memory and may damage the unit.

TROUBLESHOOTING

OTHERS

29