Timer Recording

9Turn the ADJUST dial to set the recording speed:

SP = standard play; EP = extended play; AUTO = auto. Auto speed programming is discussed on page 48. Turn the SHUTTLE ring to the right.

IMPORTANT

If you turn the SHUTTLE ring to the right when you set the timer recording incompletely, Program is not completed will appear on your screen.

If two programmed recording times overlap, VCR is already programmed for that time will display on your screen for about 3 seconds, and then the Recap screen will appear. The program you have just set will flash for 3 seconds and the start time and the stop time will be shown in red letters. The start and stop time of the overlapped program will be highlighted in red color. You will need to erase one of them.

10The programmed memory will appear on the Recap screen. ÒSÓ next to the channel number indicates satellite channels.

11To program additional recording times, select an empty program line by turning ADJUST dial. Turn the SHUTTLE ring to the right. The VCR Plus+ system menu will appear. Continue the programming procedure from step 3.

12When you are finished entering the programs you wish to record, check the following:

¥If you have a cable box, a digital cable box, a PRIMESTAR¨ or a DISH Networkª satellite receiver, leave the cable box or receiver turned ON.

¥If your VCR does not control your cable box, leave the box tuned to the station you wish to record.

¥Turn the VCR power OFF and make sure the programmed recording light is lit.

IMPORTANT

When programmed recordings of 4 and under are entered, only 4 of the 8 program lines appear on the Recap screen at any one time. To see additional program lines, turn the ADJUST dial to scroll the lines on the screen.

Cancelling a Recording in Progress

There are two ways to cancel a recording in progress:

Press STOP. The recording stops, but the program is not cancelled. There- fore, if you press REC, the recording will start again.

Press POWER on the front panel. The recording stops and the program is cancelled.

 

 

 

 

 

 

 

ÂProgram to record￿

 

 

 

ÄChannel

 

2￿

 

 

ÄDay

Monday 12￿

 

 

ÄStart time

 

11:30am￿

 

ÄStop time

 

1:30pm￿

 

 

 

 

 

ÄRecord speed

SP￿

 

¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹￿

 

Use ADJUST to select,￿

 

 

 

and ENTER.￿

 

 

 

 

 

Press MENU to go back.

 

 

 

 

 

 

 

 

Recap screen

ÂProgram to record￿

CH DAY ON OFF￿

10 TH15 9:00p10:30pSP￿

¤2 MO12 11:30a 1:30pSP￿

----- --:-- --:-- SP￿

----- --:-- --:-- SP￿

¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹¹￿ Use ADJUST to select,￿ and ENTER.￿

Press MENU to go back.

Programming not cancelled

STOP

STOP

Programming cancelled

POWER

Changing while Programming

To change one of your settings (such as start time) while you are programming:

Turn the SHUTTLE ring to the right to move forward through the program list. Turn the SHUTTLE ring to the left to move backward.

Then use ADJUST dial to change the setting.

You will cancel the entire program if you turn the shuttle ring to the left while the channel number is flashing.

backward forward

ADJUST

shuttle ring

41

Page 43
Image 43
Mitsubishi Electronics HS-HD2000U manual Cancelling a Recording in Progress, Changing while Programming