Humidity range 20-90% noncondensing | Multi-Tech Systems RAS96

RAS96 RASCard User Guide

•Humidity range: 20–90% (noncondensing).

•Power consumption: 4.5 A @ +5 VDC.

•Limited warranty: Two years.

4	CommPlete Communications Server

Image 10

Multi-Tech Systems RAS96 manual Humidity range 20-90% noncondensing

Contents

RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Important Safety Instructions Iii Table of Contents Solving Problems Appendix C Post CodesPage Introduction Introduction Manual Organization Appendix C Post Codes Technical SpecificationsAppendix B Post Messages Appendix D Approved Memory Humidity range 20-90% noncondensing RASCard Description Memory Banks RAS96 RASCard Jumpers J17 Watchdog TimerJ14, J15, J16, J18 CPU Frequency Selection Internal Connectors J22 E1 Alarm External ConnectorsJ2 Power Connector J35 Video Ethernet Status LEDs LED IndicatorsFront Panel E1 Status LEDs Power Switch SwitchesReset Switch Page Installation Pre-Installation Notes Safety WarningsInstallation Procedure Installation Page Bios Setup Utility Starting Setup Case of Problems Using SetupGetting Help Chipset Features Setup Standard Cmos SetupBios Features Setup Power Management Setup Password Setting PCI Configuration SetupLoad Bios Defaults Load Setup Defaults IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Time Standard Cmos SetupDate Hard Disks Video Drive a Type / Drive B TypeCGA Halt On Memory Disabled Bios Features SetupEnabled Virus Warning Boot Up Floppy Seek Quick Power On Self TestBoot Sequence Boot Up NumLock Status Memory Parity Check Typematic Rate SettingGate A20 Option Typematic Rate Chars/Sec Security Option Typematic Delay MsecVideo Bios Shadow C8000 Cffff Shadow/DC000 Dffff Shadow System Bios Cacheable Chipset Features SetupDram Timing IDE HDD Block Mode Video Bios CacheableBit I/O Recovery Time Memory Hole At 15M-16M PCI Streaming On-Chip Primary PCI IDEPCI Concurrancy PCI Bursting Power Management Setup Power Management Suspend Mode Doze ModeStandby Mode HDD Power Down LPT Ports Accessed Power Down ActivitiesCOM Ports Accessed Drive Ports Accessed Slot x Using INT# PCI Configuration Setup1st/2nd/3rd/4th Available IRQ PCI IRQ Activated by PCI IDE IRQ Map to Password Setting Enter PasswordPage E1 Daughter Cards Specifications E1 Overview E1 Glossary E1 Basics E1 Line Coding Signaling OptionsE1 Frame Formats Dnis digits Country Selection Pin Signal E1 Facility Termination E1 Line Monitoring Jack RJ-11 Alarm JackPCB Description Test Modes Channelized E1 line with 30 DS-0 channels E1 Frame Format Configuration of the E1 Daughter CardOrdering an E1 Line Line Coding To Configure the E1 Daughter Card Factory Defaults E1 Commands Command Example RAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Command Messages E1 Status LEDs Functional Description Solving Problems Troubleshooting RASCard has no video COM1 port does not respond correctly Invalid time, date or setupKeyboard does not respond to key strokes Memory Upgrade Diagnostic Tests Calling Technical Support RAS96 RASCard User Guide Appendixes Keyboard Connector J11 Appendix a Connector PinoutsVideo Connector J35 COM1 Connector J3 E1 Alarm Connector J22 Pin Floppy Disk Drive Connector J27 Drive Power Connector J13 Hard Disk Connector J6 IOCS16 IDE Connector J21 Figure A-7. IDE connector Appendix B Post Messages Error MessagesPost Beep Memory parity Error at Memory Address Error atMemory Verify Error at Offending Segment Appendix C Post Codes Code Name Description Post Codes E1-EF Appendix D Approved Memory Capacity Speed Type Manufacturer Part Number Usable MB EMC, Safety and Terminal Directive Compliance Appendix E Regulatory Information